会员中心 | English

开槽短圆柱端紧定螺钉 [Table 5] (A307, SAE J429, F468, F593) ASME/ANSI B 18.6.2 (T5 half-dog) - 1998 (R2010)

选择规格尺寸点击↓

0# 0.0600

1# 0.0730

2# 0.0860

3# 0.0990

4# 0.1120

5# 0.1250

6# 0.1380

8# 0.1640

10# 0.1900

12# 0.2160

1/4 0.2500

5/16 0.3125

3/8 0.3750

7/16 0.4375

1/2 0.5000

9/16 0.5625

5/8 0.6250

3/4 0.7500

ASME/ANSI B 18.6.2 (T5 half-dog) - 1998 (R2010) 开槽短圆柱端紧定螺钉 [Table 5] (A307, SAE J429, F468, F593)

尺寸单位: inch

美标ASME/ANSI B18.6.2 (T5 half-dog) - 1998 开槽短圆柱端紧定螺钉 [Table 5] (A307, SAE J429, F468, F593)

扫一扫分享

公差美制螺纹极限尺寸米/英制螺纹对照螺纹直径与受力截面积最小破坏扭矩牌号等级

螺纹尺寸
d

0#
0.0600

1#
0.0730

2#
0.0860

3#
0.0990

4#
0.1120

5#
0.1250

6#
0.1380

8#
0.1640

10#
0.1900

n	最大值
n	最小值
t	最大值
t	最小值
d_p	最大值
d_p	最小值
z	最大值
z	最小值
α	+5°

0.014	0.016	0.018	0.020	0.024	0.026	0.028	0.032	0.035
0.010	0.012	0.014	0.016	0.018	0.020	0.022	0.026	0.029
0.020	0.020	0.025	0.028	0.031	0.036	0.040	0.046	0.053
0.016	0.016	0.019	0.022	0.025	0.026	0.030	0.036	0.043
0.040	0.049	0.057	0.066	0.075	0.083	0.092	0.109	0.127
0.037	0.045	0.053	0.062	0.070	0.078	0.087	0.103	0.120
0.017	0.021	0.024	0.027	0.030	0.033	0.038	0.043	0.050
0.013	0.017	0.020	0.023	0.026	0.027	0.032	0.037	0.040
35°	35°	35°	35°	35°	35°	35°	35°	35°

螺纹尺寸
d

12#
0.2160

1/4
0.2500

5/16
0.3125

3/8
0.3750

7/16
0.4375

1/2
0.5000

9/16
0.5625

5/8
0.6250

3/4
0.7500

n	最大值
n	最小值
t	最大值
t	最小值
d_p	最大值
d_p	最小值
z	最大值
z	最小值
α	+5°

0.042	0.049	0.055	0.068	0.076	0.086	0.096	0.107	0.134
0.035	0.041	0.047	0.060	0.068	0.076	0.086	0.097	0.124
0.061	0.068	0.083	0.099	0.114	0.130	0.146	0.161	0.193
0.051	0.058	0.073	0.089	0.104	0.120	0.136	0.151	0.183
0.144	0.156	0.203	0.250	0.297	0.344	0.391	0.469	0.562
0.137	0.149	0.195	0.241	0.287	0.334	0.379	0.456	0.549
0.060	0.068	0.083	0.099	0.114	0.130	0.146	0.164	0.196
0.050	0.058	0.073	0.089	0.104	0.120	0.134	0.148	0.180
35°	35°	35°	35°	35°	35°	35°	35°	35°

①,当以小数表示公称尺寸时，应省略小数点前和小数点后第四位的零。

替代列表

ASME/ANSI B 18.6.2T5 half-dog - 1998(R2010) ASME B 18.6.2T3-Half Dog - 2020

引用参考

GB /T 1172 - 1999

黑色金属硬度及强度换算值

GB /T 5267.1 - 2002

镀锌、镀镍、镀镉、复合镀等层镀层盐雾腐蚀的防护性能

GB /T 193 - 2003

普通螺纹（一般用途米制螺纹）- 直径与螺距系列 (ISO 261: 1998, MOD)

GB /T 3106 - 2016

紧固件 - 螺栓、螺钉和螺柱 - 公称长度和螺纹长度 (ISO 888:2012, MOD)

GB /T 3 - 1997

普通螺纹收尾、肩距、退刀槽和倒角 (ISO 3508:1976 / ISO 4755:1983)

GB /T 5779.1 - 2000

紧固件表面缺陷 - 螺栓、螺钉和螺柱 - 一般要求

GB /T 5779.3 - 2000

紧固件表面缺陷 - 螺栓、螺钉和螺柱 - 特殊要求

注：技术数据仅供参考，请以官方原件为准！

类似标准及供货信息

1	[国标] GB /T 75 - 2018	开槽长圆柱端紧定螺钉 Slotted Set Screws with Long Dog Point 供应商(1)
2	[国标] GB 75 - 1985	开槽长圆柱端紧定螺钉 Slotted Set Screws with Long Dog Point 供应商(1)
3	[国标] GB /T 829 - 1988	开槽圆柱端定位螺钉 Slotted Set Screws with Dog Point
4	[德标] DIN 926 - 2003	开槽球面圆柱端紧定螺钉 Slotted Set Screws with Dog Point
5	[德标] DIN 417 - 1986	开槽长圆柱端紧定螺钉 Slotted Set Screws with Long Dog Point
6	[德标] DIN 926 - 1986	开槽球面圆柱端紧定螺钉 Slotted Set Screws with Full Dog Point
7	[国际] ISO 7435 - 2024	开槽圆柱端紧定螺钉 Slotted Set Screws With Long Dog Point
8	[国际] ISO 7435 - 1983	开槽圆柱端紧定螺钉 Slotted Set Screws with Long Dog Point
9	[日标] JIS B 1117 (T4) - 2010	开槽圆柱端紧定螺钉 Slotted Set Screws with Long Dog Point
10	[日标] JIS B 1117 (T3) - 1995	开槽圆柱端紧定螺钉 Slotted Set Screws with Long Dog Point
11	[美标] ASME/ANSI B 18.6.2 (T5-dog) - 1998 (R2010)	开槽长圆柱端紧定螺钉 [Table 5] (A307, SAE J429, F468, F593) Slotted Set Screws with Long Dog Point [Table 5] (A307, SAE J429, F468, F593)
12	[欧标] EN 27435 - 1992	开槽长圆柱端紧定螺钉 Slotted Set Screws with Long Dog Point
13	[法国] NF E 25-162 - 1992 (R2002)	开槽长圆柱端紧定螺钉 Slotted Set Screws with Long Dog Point
14	[台湾] CNS 4653 - 1983	开槽球面柱端螺钉 Slotted Set Screws with Dog Point and Round End
15	[台湾] CNS 4475 - 1981	开槽圆柱端紧定螺钉 Slotted Set Screws with Dog Piont
16	[德标] DIN EN 27435 - 1992	开槽长圆柱端紧定螺钉 Slotted Set Screws with Long Dog Point
17	[美标] ASME B 18.6.2 (T3-Dog) - 2020	开槽长圆柱端紧定螺钉 (A307, SAE J429, F468, F593) Slotted Set Screws with Long Dog Point (A307, SAE J429, F468, F593)
18	[美标] ASME B 18.6.2 (T3-Half Dog) - 2020	开槽短圆柱端紧定螺钉 (A307, SAE J429, F468, F593) Slotted Set Screws with Short Dog Point (A307, SAE J429, F468, F593)
19	[航天] QJ 2379 - 1992	开槽球面柱端螺钉 Slotted Set Screws with Dog Piont and Round End