index
会员中心 | English
logo
首页 产品与标准 GB /T 846 - 1985 十字槽沉头自攻钉

十字槽沉头自攻钉 GB /T 846 - 1985

选择规格尺寸 点击↓

ST2.2

ST2.9

ST3.5

ST4.2

ST4.8

ST5.5

ST6.3

ST8

ST9.5

GB /T 846 - 1985 十字槽沉头自攻钉

尺寸单位: mm
国标GB /T846 - 1985 GB846 846GB 十字槽沉头自攻钉
国标GB /T846 - 1985 GB846 846GB 十字槽沉头自攻钉
模型下载 替
GB /T 846 - 1985 十字槽沉头自攻钉
扫一扫分享
单重计算 公差
千件重及价格计算 千件重 : kg x 元/kg = 元/千件
默认密度 g/cm3
×

选择材料对应密度(g/cm3)

  • 碳钢 7.85
  • 不锈钢 8.1
  • 不锈钢 7.95
  • 不锈钢 7.7
  • 钛合金 4.5
  • 铝合金 2.8
  • 铜 8.89


在此选择或在计算页输入材料密度 密度表
公称长度L 注:选择后获得 相应重量
螺纹规格
d
ST2.2 ST2.9 ST3.5 ST4.2 ST4.8 ST5.5 ST6.3 ST8 ST9.5
P 螺距
a 最大值
dk 理论 最大值
实际 最大值
最小值
k 最大值
槽号
M1 H型 参考
深度 H型 最小值
最大值
M2 Z型 参考
深度 Z型 最小值
最大值
y 参考 C型
F型
0.8 1.1 1.3 1.4 1.6 1.8 1.8 2.1 2.1
0.8 1.1 1.3 1.4 1.6 1.8 1.8 2.1 2.1
4.4 6.3 8.2 9.4 10.4 11.5 12.6 17.3 20
3.8 5.5 7.3 8.4 9.3 10.3 11.3 15.8 18.3
3.5 5.2 6.9 8 8.9 9.9 10.9 15.4 17.8
1.1 1.7 2.35 2.6 2.8 3 3.15 4.65 5.25
0 1 2 2 2 3 3 4 4
1.9 3.2 4.4 4.6 5.2 6.6 6.8 8.9 10
0.9 1.7 1.9 2.1 2.7 2.8 3 4 5.1
1.2 2.1 2.4 2.6 3.2 3.3 3.5 4.6 5.7
2 3.2 4.3 4.6 5.1 6.5 6.8 9 10
0.95 1.6 1.75 2.05 2.6 2.75 3 4.15 5.2
1.2 2 2.2 2.5 3.05 3.2 3.45 4.6 5.65
2 2.6 3.2 3.7 4.3 5 6 7.5 8
1.6 2.1 2.5 2.8 3.2 3.6 3.6 4.2 4.2
千件钢制重≈kg
- - - - - - - - -
替代列表
GB 846 - 1976 GB /T 846 - 1985 GB /T 846 - 2017
等效标准
国标 GB 国际 ISO 德标 DIN 意大利 UNI
GB /T 846
ISO 7050
DIN EN ISO 7050
UNI 6955
以上有部分标准可能为近似等效，如有异议以标准原件为准

采用标准

工艺相关

GB /T 5280
自攻螺钉用螺纹
GB /T 3098.5
紧固件机械性能 自攻螺钉
GB /T 3103.1
紧固件公差（螺栓、螺柱、螺钉和螺母）
GB 944.1
螺钉用十字槽
GB /T 5279
沉头螺钉头部配置和测量
GB /T 5267.1
电镀层厚度的技术要求
GB /T 90.1
紧固件 验收检查 （ISO 3269:2000 IDT）
GB /T 90.2
紧固件 标志与包装
GB /T 1237
紧固件标记方法

技术条件和引用标准

螺纹
机械性能
公差 产品等级
标准
十字槽
沉头的测量
表面处理
验收及包装
GB 5280
GB 3098.5
除规定外，其余按A级
GB 3103.1
GB 944.1
GB 5279
镀锌钝化 GB 5267
GB 90

引用参考

GB /T 3098.5
紧固件机械性能 - 自攻螺钉
GB /T 1172 - 1999
黑色金属硬度及强度换算值
GB /T 5267.1 - 2002
镀锌、镀镍、镀镉、复合镀等层镀层盐雾腐蚀的防护性能
GB /T 193 - 2003
普通螺纹（一般用途米制螺纹）- 直径与螺距系列 (ISO 261: 1998, MOD)
GB /T 5280 - 2002
自攻螺钉用螺纹
注：技术数据仅供参考，请以官方原件为准！
告诉我在“易紧通”看到，将给您优惠
上海承泰金属五金制造有限公司
联系人：诸葛鸿满 点击这里给我发消息2880137050 点击这里给我发消息2880137059   移动电话： 18916049888     电话：021-59742477/59740118 Email: 登陆后可见
材质：不锈钢；规格：齐全；表面处理：根据客户要求
[询价]
苏州市桂丰精密不锈钢紧固件厂
联系人：杨钦   移动电话： 15162465399     电话：0512-65808790 Email: 登陆后可见
材料：碳钢、不锈钢，表面处理：本色; 公称直径：M1.2-M8,公称长度：3mm-80mm
[询价]
瑞安市亿品不锈钢制品有限公司
联系人：薛兵兵 点击这里给我发消息1248985748   移动电话： 13353381559     电话：0577-65515520     微信号：13353381559 Email: 登陆后可见
材质：不锈钢200 304 316，规格范围：ST2.2-ST6.3
[询价]
句容市大进标准件制造有限责任公司
联系人：尚云梅 点击这里给我发消息624698130   移动电话： 13400093205     电话：0511-87881576     微信号：qw624698130 Email: 登陆后可见
材质：碳钢、不锈钢200、 304 、316；规格范围：M2-M10；公称长度：5-200mm；表面处理：镀白锌、彩锌、镍、达克罗、抛光等。现货充足
[询价]
青岛永新金属制品有限公司
联系人：王经理 点击这里给我发消息2853639927   移动电话： 18678916777     电话：0532-87980778 Email: 登陆后可见
供应“青固”品牌螺丝，0.8φ-20φ碳钢1022、不锈钢 304 、316、302； 铜、铝等材质；2.5-10mm，公称长度：6.5mm-300mm ；表面处理：镀白锌、彩锌、镍、达克罗、热镀锌等；非标按客户要求定做。
[询价]
苏州永创紧固件厂
联系人：汤继勇 点击这里给我发消息546348066   移动电话： 15298892886     电话：0512-66700967 Email: 登陆后可见
材质：不锈钢、碳钢；公称直径范围：M1-M14；公称长度范围：5-400mm
[询价]
南京福贝尔五金制品有限公司
联系人：杨帆（销售经理） 点击这里给我发消息2850588398   移动电话： 13813085707     电话：025-52758402,52758403,52758406分机：8859/8858 Email: 登陆后可见
材料：碳钢、合金钢、304、304L、316、316L、双相钢2205、2507、2520、C1-70、C1-110、C3-80、904L、310S、1CR13、2CR13、蒙乃尔K500、1.4529、高温高压合金钢、防腐合金钢等；等级：A2-70、A2-80、A4-80、8.8级、10.9级\12.9级以上；表面处理：本色、钝化、镀锌、达克罗、发黑等；规格范围：M6-M56,可按图定制
[询价]
告诉我在“易紧通”看到，将给您优惠
类似标准及供货信息
1 十字槽沉头自攻钉 [国标]
GB /T 846 - 2017		 十字槽沉头自攻钉
Cross Recessed Countersunk Head Tapping Screws
供应商(7)
2 十字槽沉头自攻螺钉 [国标]
GB 846 - 1976		 十字槽沉头自攻螺钉
Cross recessed countersunk head self-tapping screws
供应商(7)
3 十字槽沉头自攻钉 [德标]
DIN 7982 - 1990		 十字槽沉头自攻钉
Cross recessed countersunk head tapping screws
供应商(3)
4 十字槽沉头自攻螺钉 [国际]
ISO 7050 - 2011		 十字槽沉头自攻螺钉
Cross Recessed Countersunk (Flat) Head Tapping Screws
供应商(1)
5 十字槽沉头自攻螺钉 [国际]
ISO 7050 - 1983		 十字槽沉头自攻螺钉
Cross recessed countersunk head tapping screws
供应商(1)
6 十字槽喇叭头自攻钉 [日标]
JIS B 1125 - 2015		 十字槽喇叭头自攻钉
Cross Recessed Trumpet Head Self Drilling Tapping Screw
7 十字槽沉头带筋自攻钉 [日标]
JIS B 1125 - 2015		 十字槽沉头带筋自攻钉
Flex. Purpose Drilling Tapping Screws
8 十字槽喇叭头自攻钉 [日标]
JIS B 1125 - 2003		 十字槽喇叭头自攻钉
cross recessed trumpet head self drilling tapping screw
9 十字槽沉头带筋自攻钉 [日标]
JIS B 1125 - 2003		 十字槽沉头带筋自攻钉
Cross recessed ribbed countersunk head tapping screws
10 十字槽沉头自攻钉 - 螺纹型式：Class 1~Class 4【附表2】 [日标]
JIS B 1122 (AAT2) - 1996		 十字槽沉头自攻钉 - 螺纹型式：Class 1~Class 4【附表2】
Cross Recessed Countersunk Head Tapping Screws - threaded portion are of class 1 to 4 [Annex attached table 2]
11 十字槽沉头自攻钉 【表2】 [日标]
JIS B 1122 (AT2) - 1996		 十字槽沉头自攻钉 【表2】
Cross recessed countersunk head tapping screws [Table 2]
12 十字槽喇叭头自攻钉 [日标]
JIS B 1125 - 1995		 十字槽喇叭头自攻钉
Cross recessed bugle head self-drilling tapping screws
13 十字槽沉头自攻螺钉 C型 [汽标代号]
Q 274		 十字槽沉头自攻螺钉 C型
Cross recessed countersunk head tapping screws - Type C
14 十字槽沉头自攻螺钉 F型 [汽标代号]
Q 278		 十字槽沉头自攻螺钉 F型
Cross recessed countersunk head tapping screws - Type F
15 80°十字槽沉头自攻钉 [美标]
ASME/ANSI B 18.6.3 - 2010		 80°十字槽沉头自攻钉
80° Machine Screw and Tapping Screw Nuts (Inch Seires)
16 塑料用双螺纹十字槽沉头(平头)自攻螺钉 [意大利]
UNI 9709 - 1990		 塑料用双螺纹十字槽沉头(平头)自攻螺钉
Two-thread countersunk (flat) head tapping screws with cross rocessed for plastics
17 十字槽沉头自攻钉 [意大利]
UNI 6955		 十字槽沉头自攻钉
Cross-Recessed Flat Countersunk Head Tapping Screws
18 十字槽沉头自攻螺钉 [法国]
NF E 25-656 - 1994		 十字槽沉头自攻螺钉
Cross Recessed Countersunk (Flat) Head Tapping Screws
19 米字槽80°沉头自攻钉 [Table 9] [英标]
BS 4174 - 1972		 米字槽80°沉头自攻钉 [Table 9]
Recess 80°countersunk Head Screws - Type Z [Table 9]
20 米字槽80°沉头清根自攻钉 [Table 11] [英标]
BS 4174 - 1972		 米字槽80°沉头清根自攻钉 [Table 11]
Recess 80°Truncated Countersunk Head Screws - Type Z [Table 11]
21 米制十字槽沉头自攻螺钉 [澳标]
AS /NZS 4407 - 1996		 米制十字槽沉头自攻螺钉
ISO metric cross recessed countersunk head tapping screws
22 十字槽沉头自攻钉 [原电子工业部]
SJ 2822 - 1987		 十字槽沉头自攻钉

23 十字槽沉头自攻钉 [原电子工业部]
SJ 2498 - 1984		 十字槽沉头自攻钉

24 十字槽沉头自攻螺钉 [韩标]
KS B 1032 - 2016 (R2021)		 十字槽沉头自攻螺钉
Cross-Recessed Countersunk (Flat) Head Tapping Screws
25 十字槽沉头自攻螺钉 [韩标]
KS B 1032 - 2001		 十字槽沉头自攻螺钉
Cross-Recessed Countersunk (Flat) Head Tapping Screws
26 十字槽沉头自攻螺钉 [企标]
YJT 4058 (WN1413C)		 十字槽沉头自攻螺钉
Cross recessed countersunk head Tapping screws
供应商(1)
27 十字槽沉头自攻螺钉 [德标]
DIN EN ISO 7050 - 2011		 十字槽沉头自攻螺钉
Cross Recessed Countersunk (Flat) Head Tapping Screws
供应商(3)
28 十字槽82度沉头AB ABR自攻螺钉 [美标]
ASME B 18.6.3 (H1B-I/H1B-IA+T1A) - 2024		 十字槽82度沉头AB ABR自攻螺钉
82° Cross Recessed Countersunk Head Tapping Screws - Type AB (ABR)
29 十字槽82°沉头清根 AB ABR自攻螺钉 [美标]
ASME B 18.6.3 (H3B-I/H3B-IA+T1A) - 2024		 十字槽82°沉头清根 AB ABR自攻螺钉
Undercut 82-deg Flat Countersunk Head Tapping Screws - Type AB (ABR)
30 十字槽小沉头 AB ABR自攻螺钉 [美标]
ASME B 18.6.3 (H4B-I/H4B-IA+T1A) - 2024		 十字槽小沉头 AB ABR自攻螺钉
Flat Coutersunk Trim Head Tapping Screws - Type AB and ABR
31 十字槽82度沉头AB ABR自攻螺钉 [美标]
ASME B 18.6.3 (T2-I/T2-IA+T40) - 2013		 十字槽82度沉头AB ABR自攻螺钉
82° Cross Recessed Countersunk Head Tapping Screws - Type AB (ABR)
32 十字槽82°沉头清根 AB ABR自攻螺钉 [美标]
ASME B 18.6.3 (T10-I/T10-IA+T40) - 2013		 十字槽82°沉头清根 AB ABR自攻螺钉
Undercut 82-deg Flat Countersunk Head Tapping Screws - Type AB (ABR)
33 十字槽小沉头 AB ABR自攻螺钉 [美标]
ASME B 18.6.3 (T14-I/T14-IA+T40) - 2013		 十字槽小沉头 AB ABR自攻螺钉
Flat Coutersunk Trim Head Tapping Screws - Type AB and ABR
34 米制米字槽沉头自攻螺钉 [Table 10] [美标]
ASME B 18.6.5M (T10) - 2000 (R2010)		 米制米字槽沉头自攻螺钉 [Table 10]
Metric Type IA Cross-Recessed Flat Countersunk Head Tapping Screws [Table 10]
35 米制十字槽沉头自攻螺钉 [Table 9] [美标]
ASME B 18.6.5M (T9) - 2000 (R2010)		 米制十字槽沉头自攻螺钉 [Table 9]
Metric cross recessed countersunk head tapping screws [Table 9]
36 I型十字槽沉头自攻螺钉 A型 [Table 10] [美标]
ASME B 18.6.4 - 1998 (R2005)		 I型十字槽沉头自攻螺钉 A型 [Table 10]
Type I Cross Recessed Flat Countersunk Head Tapping Screws - Type A Thread Forming [Table 10]
37 I型十字槽沉头自攻螺钉 B, BP型 [Table 10] [美标]
ASME B 18.6.4 - 1998 (R2005)		 I型十字槽沉头自攻螺钉 B, BP型 [Table 10]
Type I Cross Recessed Flat Countersunk Head Tapping Screws - Type B and BP Thread Forming [Table 10]
38 I型十字槽沉头自攻螺钉 C型 (统一螺纹) [Table 10] [美标]
ASME B 18.6.4 - 1998 (R2005)		 I型十字槽沉头自攻螺钉 C型 (统一螺纹) [Table 10]
Type I Cross Recessed Flat Countersunk Head Tapping Screws - Type C Thread Forming [Table 10]
39 I型十字槽沉头自攻螺钉 AB型 [Table 10] [美标]
ASME B 18.6.4 - 1998 (R2005)		 I型十字槽沉头自攻螺钉 AB型 [Table 10]
Type I Cross Recessed Flat Countersunk Head Tapping Screws - Type AB Thread Forming [Table 10]
40 IA型米字槽沉头自攻螺钉 A型 [Table 11] [美标]
ASME B 18.6.4 - 1998 (R2005)		 IA型米字槽沉头自攻螺钉 A型 [Table 11]
Type IA Cross Recessed Flat Countersunk Head Tapping Screws - Type A Thread Forming [Table 11]
41 IA型米字槽沉头自攻螺钉 B,BP型 [Table 11] [美标]
ASME B 18.6.4 - 1998 (R2005)		 IA型米字槽沉头自攻螺钉 B,BP型 [Table 11]
Type I Cross Recessed Flat Countersunk Head Tapping Screws - Type B and BP Thread Forming [Table 11]
42 IA型米字槽沉头自攻螺钉 C型(统一螺纹) [Table 11] [美标]
ASME B 18.6.4 - 1998 (R2005)		 IA型米字槽沉头自攻螺钉 C型(统一螺纹) [Table 11]
Type I Cross Recessed Flat Countersunk Head Tapping Screws - Type C Thread Forming [Table 11]
43 IA型米字槽沉头自攻螺钉 AB型 [Table 11] [美标]
ASME B 18.6.4 - 1998 (R2005)		 IA型米字槽沉头自攻螺钉 AB型 [Table 11]
Type I Cross Recessed Flat Countersunk Head Tapping Screws - Type AB Thread Forming [Table 11]
44 II型十字槽沉头自攻螺钉 A型 [Table 12] [美标]
ASME B 18.6.4 - 1998 (R2005)		 II型十字槽沉头自攻螺钉 A型 [Table 12]
Type II Cross Recessed Flat Countersunk Head Tapping Screws - Type A Thread Forming [Table 12]
45 II型十字槽沉头自攻螺钉 B，BP型 [Table 12] [美标]
ASME B 18.6.4 - 1998 (R2005)		 II型十字槽沉头自攻螺钉 B，BP型 [Table 12]
Type II Cross Recessed Flat Countersunk Head Tapping Screws - Type B and BP Thread Forming [Table 12]
46 II型十字槽沉头自攻螺钉 C型(统一螺纹) [Table 12] [美标]
ASME B 18.6.4 - 1998 (R2005)		 II型十字槽沉头自攻螺钉 C型(统一螺纹) [Table 12]
Type II Cross Recessed Flat Countersunk Head Tapping Screws - Type C Thread Forming [Table 12]
47 II型十字槽沉头自攻螺钉 AB型 [Table 12] [美标]
ASME B 18.6.4 - 1998 (R2005)		 II型十字槽沉头自攻螺钉 AB型 [Table 12]
Type II Cross Recessed Flat Countersunk Head Tapping Screws - Type AB Thread Forming [Table 12]
48 I型十字槽沉头清根自攻螺钉 B,BP型 [Table 14] [美标]
ASME B 18.6.4 - 1998 (R2005)		 I型十字槽沉头清根自攻螺钉 B,BP型 [Table 14]
Type I Cross Recessed Undercut Flat Countersunk Head Tapping Screws - Type B and BP Thread Forming [Table 14]
49 I型十字槽沉头清根自攻螺钉 C型(统一螺纹) [Table 14] [美标]
ASME B 18.6.4 - 1998 (R2005)		 I型十字槽沉头清根自攻螺钉 C型(统一螺纹) [Table 14]
Type I Cross Recessed Undercut Flat Countersunk Head Tapping Screws - Type C Thread Forming [Table 14]
50 I型十字槽沉头清根自攻螺钉 AB型 [Table 14] [美标]
ASME B 18.6.4 - 1998 (R2005)		 I型十字槽沉头清根自攻螺钉 AB型 [Table 14]
Type I Cross Recessed Undercut Flat Countersunk Head Tapping Screws - Type AB Thread Forming [Table 14]
51 IA型米字槽沉头清根自攻螺钉 B,BP型 [Table 15] [美标]
ASME B 18.6.4 - 1998 (R2005)		 IA型米字槽沉头清根自攻螺钉 B,BP型 [Table 15]
Type IA Cross Recessed Undercut Flat Countersunk Head Tapping Screws - Type B and BP Thread Forming [Table 15]
52 IA型米字槽沉头清根自攻螺钉 C型(统一螺纹) [Table 15] [美标]
ASME B 18.6.4 - 1998 (R2005)		 IA型米字槽沉头清根自攻螺钉 C型(统一螺纹) [Table 15]
Type IA Cross Recessed Undercut Flat Countersunk Head Tapping Screws - Type C Thread Forming [Table 15]
53 IA型米字槽沉头清根自攻螺钉 AB型 [Table 15] [美标]
ASME B 18.6.4 - 1998 (R2005)		 IA型米字槽沉头清根自攻螺钉 AB型 [Table 15]
Type IA Cross Recessed Undercut Flat Countersunk Head Tapping Screws - Type AB Thread Forming [Table 15]
54 II型十字槽沉头清根自攻螺钉 B,BP型 [Table 16] [美标]
ASME B 18.6.4 - 1998 (R2005)		 II型十字槽沉头清根自攻螺钉 B,BP型 [Table 16]
Type II Cross Recessed Undercut Flat Countersunk Head Tapping Screws - Type B and BP Thread Forming [Table 16]
55 II型十字槽沉头清根自攻螺钉 C型(统一螺纹) [Table 16] [美标]
ASME B 18.6.4 - 1998 (R2005)		 II型十字槽沉头清根自攻螺钉 C型(统一螺纹) [Table 16]
Type II Cross Recessed Undercut Flat Countersunk Head Tapping Screws - Type C Thread Forming [Table 16]
56 II型十字槽沉头清根自攻螺钉 AB型 [Table 16] [美标]
ASME B 18.6.4 - 1998 (R2005)		 II型十字槽沉头清根自攻螺钉 AB型 [Table 16]
Type II Cross Recessed Undercut Flat Countersunk Head Tapping Screws - Type AB Thread Forming [Table 16]
57 I型十字槽沉头精整自攻螺钉,B,BP型 [Table 17] [美标]
ASME B 18.6.4 - 1998 (R2005)		 I型十字槽沉头精整自攻螺钉,B,BP型 [Table 17]
Type I Cross Recessed Flat Countersunk Trim Head Tapping Screws - Type B and BP Thread Forming [Table 17]
58 I型十字槽沉头精整自攻螺钉,C型(统一螺纹) [Table 17] [美标]
ASME B 18.6.4 - 1998 (R2005)		 I型十字槽沉头精整自攻螺钉,C型(统一螺纹) [Table 17]
Type I Cross Recessed Flat Countersunk Trim Head Tapping Screws - Type C Thread Forming [Table 17]
59 I型十字槽沉头精整自攻螺钉,AB型 [Table 17] [美标]
ASME B 18.6.4 - 1998 (R2005)		 I型十字槽沉头精整自攻螺钉,AB型 [Table 17]
Type I Cross Recessed Flat Countersunk Trim Head Tapping Screws - Type AB Thread Forming [Table 17]
60 I型十字槽沉头精整自攻螺钉,A型 [Table 17] [美标]
ASME B 18.6.4 - 1998 (R2005)		 I型十字槽沉头精整自攻螺钉,A型 [Table 17]
Type I Cross Recessed Flat Countersunk Trim Head Tapping Screws - Type A Thread Forming [Table 17]
61 IA型十字槽沉头精整自攻螺钉 B,BP型 [Table 18] [美标]
ASME B 18.6.4 - 1998 (R2005)		 IA型十字槽沉头精整自攻螺钉 B,BP型 [Table 18]
Type IA Cross Recessed Flat Countersunk Trim Head Tapping Screws - Type B and BP Thread Forming [Table 18]
62 IA型十字槽沉头精整自攻螺钉 C型(统一螺纹) [Table 18] [美标]
ASME B 18.6.4 - 1998 (R2005)		 IA型十字槽沉头精整自攻螺钉 C型(统一螺纹) [Table 18]
Type IA Cross Recessed Flat Countersunk Trim Head Tapping Screws - Type C Thread Forming [Table 18]
63 IA型十字槽沉头精整自攻螺钉 AB型 [Table 18] [美标]
ASME B 18.6.4 - 1998 (R2005)		 IA型十字槽沉头精整自攻螺钉 AB型 [Table 18]
Type IA Cross Recessed Flat Countersunk Trim Head Tapping Screws - Type AB Thread Forming [Table 18]
64 IA型十字槽沉头精整自攻螺钉 A型 [Table 18] [美标]
ASME B 18.6.4 - 1998 (R2005)		 IA型十字槽沉头精整自攻螺钉 A型 [Table 18]
Type IA Cross Recessed Flat Countersunk Trim Head Tapping Screws - Type A Thread Forming [Table 18]
65 II型十字槽沉头精整自攻螺钉 B,BP型 [Table 19] [美标]
ASME B 18.6.4 - 1998 (R2005)		 II型十字槽沉头精整自攻螺钉 B,BP型 [Table 19]
Type II Cross Recessed Flat Countersunk Trim Head Tapping Screws - Type B and BP Thread Forming [Table 19]
66 II型十字槽沉头精整自攻螺钉 C型(统一螺纹) [Table 19] [美标]
ASME B 18.6.4 - 1998 (R2005)		 II型十字槽沉头精整自攻螺钉 C型(统一螺纹) [Table 19]
Type II Cross Recessed Flat Countersunk Trim Head Tapping Screws - Type C Thread Forming [Table 19]
67 II型十字槽沉头精整自攻螺钉 AB型 [Table 19] [美标]
ASME B 18.6.4 - 1998 (R2005)		 II型十字槽沉头精整自攻螺钉 AB型 [Table 19]
Type II Cross Recessed Flat Countersunk Trim Head Tapping Screws - Type AB Thread Forming [Table 19]
68 II型十字槽沉头精整自攻螺钉 A型 [Table 19] [美标]
ASME B 18.6.4 - 1998 (R2005)		 II型十字槽沉头精整自攻螺钉 A型 [Table 19]
Type II Cross Recessed Flat Countersunk Trim Head Tapping Screws - Type A Thread Forming [Table 19]
69 I型十字槽100°沉头自攻螺钉 B,BP型 [Table VI2] [美标]
ASME B 18.6.4 - 1998 (R2005)		 I型十字槽100°沉头自攻螺钉 B,BP型 [Table VI2]
Type I Cross Recessed 100°Flat Countersunk Head Tapping Screws - Type B and BP Thread Forming [Table VI2]
70 I型十字槽100°沉头自攻螺钉 AB型 [Table VI2] [美标]
ASME B 18.6.4 - 1998 (R2005)		 I型十字槽100°沉头自攻螺钉 AB型 [Table VI2]
Type I Cross Recessed 100°Flat Countersunk Head Tapping Screws - Type AB Thread Forming [Table VI2]
71 IA型米字槽100°沉头自攻螺钉 B,BP型 [Table VI3] [美标]
ASME B 18.6.4 - 1998 (R2005)		 IA型米字槽100°沉头自攻螺钉 B,BP型 [Table VI3]
Type IA Cross Recessed 100°Flat Countersunk Head Tapping Screws - Type B and BP Thread Forming [Table VI3]
72 IA型米字槽100°沉头自攻螺钉 AB型 [Table VI3] [美标]
ASME B 18.6.4 - 1998 (R2005)		 IA型米字槽100°沉头自攻螺钉 AB型 [Table VI3]
Type IA Cross Recessed 100°Flat Countersunk Head Tapping Screws - Type AB Thread Forming [Table VI3]
73 II型十字槽100°沉头自攻螺钉 B,BP型 [Table VI4] [美标]
ASME B 18.6.4 - 1998 (R2005)		 II型十字槽100°沉头自攻螺钉 B,BP型 [Table VI4]
Type II Cross Recessed 100°Flat Countersunk Head Tapping Screws - Type B and BP Thread Forming [Table VI4]
74 II型十字槽100°沉头自攻螺钉 AB型 [Table VI4] [美标]
ASME B 18.6.4 - 1998 (R2005)		 II型十字槽100°沉头自攻螺钉 AB型 [Table VI4]
Type II Cross Recessed 100°Flat Countersunk Head Tapping Screws - Type AB Thread Forming [Table VI4]
75 十字槽沉头自攻螺钉 [深圳紧固件行业协会标准]
T/SZJGJ 001 (C) - 2024		 十字槽沉头自攻螺钉
Cross Recessed Countersunk Head Tapping Screws
© 易紧通 服务热线：4006-164580（免长途费）