会员中心 | English

米制六角头螺钉 C级 AS 1111.2 - 2015

选择规格尺寸点击↓

M10

M12

(M14)

M16

(M18)

M20

(M22)

M24

(M27)

M30

(M33)

M36

(M39)

M42

(M45)

M48

(M52)

M56

(M60)

M64

括号内尺寸为非优选

尺寸单位: mm

澳标AS 1111.2 - 2015 AS1111.2 1111.2AS 米制六角头螺钉 C级

扫一扫分享

单重计算公差公制螺纹极限尺寸米/英制螺纹对照螺纹直径与受力截面积最小破坏扭矩牌号等级毛坯直径

螺纹尺寸
d

M10

M12

(M14)

M16

(M18)

M20

(M22)

M24

(M27)

P	螺距
a	最大值
a	最小值
c	最大值
d_a	最大值
d_w	最小值
e	最小值
k	公称
	最大值
	最小值
k₁	最小值
r	最小值
s	最大值=公称
s	最小值

0.8	1	1.25	1.5	1.75	2	2	2.5	2.5	2.5	3	3
2.4	3	4	4.5	5.3	6	6	7.5	7.5	7.5	9	9
0.8	1	1.25	1.5	1.75	2	2	2.5	2.5	2.5	3	3
0.5	0.5	0.6	0.6	0.6	0.6	0.8	0.8	0.8	0.8	0.8	0.8
6	7.2	10.2	12.2	14.7	16.7	18.7	21.2	24.4	26.4	28.4	32.4
6.74	8.74	11.47	14.47	16.47	19.15	22	24.85	27.7	31.35	33.25	38
8.63	10.89	14.2	17.59	19.85	22.78	26.17	29.56	32.95	37.29	39.55	45.2
3.5	4	5.3	6.4	7.5	8.8	10	11.5	12.5	14	15	17
3.875	4.375	5.675	6.85	7.95	9.25	10.75	12.4	13.4	14.9	15.9	17.9
3.125	3.625	4.925	5.95	7.05	8.35	9.25	10.6	11.6	13.1	14.1	16.1
2.19	2.54	3.45	4.17	4.94	5.85	6.48	7.42	8.12	9.17	9.87	11.27
0.2	0.25	0.4	0.4	0.6	0.6	0.6	0.6	0.8	0.8	0.8	1
8	10	13	16	18	21	24	27	30	34	36	41
7.64	9.64	12.57	15.57	17.57	20.16	23.16	26.16	29.16	33	35	40

螺纹尺寸
d

M30

(M33)

M36

(M39)

M42

(M45)

M48

(M52)

M56

(M60)

M64

P	螺距
a	最大值
a	最小值
c	最大值
d_a	最大值
d_w	最小值
e	最小值
k	公称
	最大值
	最小值
k₁	最小值
r	最小值
s	最大值=公称
s	最小值

3.5	3.5	4	4	4.5	4.5	5	5	5.5	5.5	6
10.5	10.5	12	12	13.5	13.5	15	15	16.5	16.5	18
3.5	3.5	4	4	4.5	4.5	5	5	5.5	5.5	6
0.8	0.8	0.8	1	1	1	1	1	1	1	1
35.4	38.4	42.4	45.4	48.6	52.6	56.6	62.6	67	71	75
42.75	46.55	51.11	55.86	59.95	64.7	69.45	74.2	78.66	83.41	88.16
50.85	55.37	60.79	66.44	71.3	76.95	82.6	88.25	93.56	99.21	104.86
18.7	21	22.5	25	26	28	30	33	35	38	40
19.75	22.05	23.55	26.05	27.05	29.05	31.05	34.25	36.25	39.25	41.25
17.65	19.95	21.45	23.95	24.95	26.95	28.95	31.75	33.75	36.75	38.75
12.36	13.97	15.02	16.77	17.47	18.87	20.27	22.23	23.63	25.73	27.13
1	1	1	1	1.2	1.2	1.6	1.6	2	2	2
46	50	55	60	65	70	75	80	85	90	95
45	49	53.8	58.8	63.1	68.1	73.1	78.1	82.8	87.8	92.8

①,机械性能等级：
d≤39mm：4.6级，4.8级（其他详见ISO 898-1）;
d＞39mm：按约定

替代列表

AS 1111.2 - 2000 AS 1111.2 - 2015

等效标准

国标 GB	国际 ISO	德标 DIN	美标 ASME/ANSI	印标 IS	澳标 AS
GB /T 5781	ISO 4018	DIN EN ISO 4018	ANSI/ASME B 18.2.3.10M	IS 1363-2	AS 1111.2

以上有部分标准可能为近似等效，如有异议以标准原件为准

引用参考

GB /T 1172 - 1999

黑色金属硬度及强度换算值

GB /T 5267.1 - 2002

镀锌、镀镍、镀镉、复合镀等层镀层盐雾腐蚀的防护性能

GB /T 193 - 2003

普通螺纹（一般用途米制螺纹）- 直径与螺距系列 (ISO 261: 1998, MOD)

GB /T 3106 - 2016

紧固件 - 螺栓、螺钉和螺柱 - 公称长度和螺纹长度 (ISO 888:2012, MOD)

GB /T 12603 - 2005

金属热处理工艺分类及代号

GB /T 3 - 1997

普通螺纹收尾、肩距、退刀槽和倒角 (ISO 3508:1976 / ISO 4755:1983)

GB /T 5779.1 - 2000

紧固件表面缺陷 - 螺栓、螺钉和螺柱 - 一般要求

GB /T 5779.3 - 2000

紧固件表面缺陷 - 螺栓、螺钉和螺柱 - 特殊要求

注：技术数据仅供参考，请以官方原件为准！

类似标准及供货信息

1	[国标] GB /T 5781 - 2016	C级全螺纹六角头螺栓 Hexagon Head Bolts - Full Thread - Product Grade C 供应商(2)
2	[国标] GB /T 5783 - 2016	全螺纹六角头螺栓 Hexagon Head Bolts - Full Thread 供应商(15)
3	[国标] GB /T 5786 - 2016	六角头螺栓细牙全螺纹 Hexagon Head Bolts with Fine Pitch Thread - Full Thread 供应商(4)
4	[国标] GB /T 5781 - 2000	C级全螺纹六角头螺栓 Hexagon head bolts -Full thread -product gradeC 供应商(2)
5	[国标] GB /T 5783 - 2000	六角头螺栓全螺纹 A级和B级 Hexagon Head Bolts - Full Thread - Grade A and B 供应商(15)
6	[国标] GB /T 5786 - 2000	六角头螺栓细牙全螺纹 Hexagon Head Bolts with Fine Pitch Thread - Full Thread 供应商(4)
7	[国标] GB 5781 - 1986	六角头螺栓 - 全螺纹 - C级 Hexagon Head Bolts - Full Thread - Product Grade C 供应商(2)
8	[国标] GB 5783 - 1986	六角头螺栓全螺纹 A级和B级 Hexagon Head Bolts - Full Thread - Product Grade A and B 供应商(15)
9	[国标] GB 5786 - 1986	六角头螺栓细牙全螺纹 Hexagon Head Bolts with Fine Pitch Thread - Full Thread 供应商(4)
10	[德标] DIN 933 - 1987	全螺纹六角头螺栓 A级和B级 Hexagon Head Screws Threaded Up To The Head - Product Grades A and B 供应商(14)
11	[德标] DIN 34810 - 2018	塑料全螺纹六角头螺钉 Plastic Hexagon Head Screws
12	[德标] DIN 34810 - 1999	塑料全螺纹六角头螺钉 Plastic hexagon head screws
13	[德标] DIN 558 - 1987	C级全螺纹六角头螺钉 Hexagon head screws-product grade C
14	[国际] ISO 4017 - 2022	六角头螺钉 A级和B级 Hexagon Head Screws - Product Grades A and B 供应商(3)
15	[国际] ISO 4017 - 2014	六角头螺钉.产品等级 A和B Hexagon Head Screws - Product Grade A And B 供应商(3)
16	[国际] ISO 4017 - 2011	六角头螺钉.产品等级 A和B Hexagon head screws with full thread-Product grade A and B 供应商(3)
17	[国际] ISO 4017 - 1999	六角头螺钉.产品等级 A和B Hexagon head screws-Product grade A and B 供应商(3)
18	[国际] ISO 4018 - 2022	六角头螺钉产品等级C Hexagon Head Screws - Product Grade C
19	[国际] ISO 4018 - 2011	六角头螺钉.产品等级C Hexagon Head Screws - Product Grade C
20	[国际] ISO 4018 - 1999	六角头螺钉.产品等级C Hexagon Head Screws-Product Grade C
21	[日标] JIS B 1180 (ISO4017) - 2014	六角头螺栓全牙产品等级：A和B级 [Figure 4] Hexagon Head Screw Bolt, Coarse, Product Grades A and B 供应商(1)
22	[日标] JIS B 1180 (ISO 4017) - 1994	六角头螺栓全螺纹产品等级：A级 [Table 5] Hexagon head bolts, Continuous thread, Procuct Grade A [Table 5] 供应商(1)
23	[日标] JIS B 1180 (ISO4018) - 2014	六角头螺栓全牙产品等级：C级 [Figure 5] Hexagon Head Screw Bolt, Coarse, Product Grade C
24	[日标] JIS B 1180 (ISO8676) - 2014	六角头螺栓细牙全螺纹产品等级：A级和B级 [Figure 6] Hexagon Head Screw Bolt, Fine thread, Product Grade A and B
25	[日标] JIS B 1180 (ISO 8676) - 1994	六角头螺栓全螺纹产品等级：B级 [Table 6] Hexagon head bolts, Continuous thread, Product Grade B [Table 6]
26	[日标] JIS B 1180 (ISO 4018) - 1994	六角头螺栓全牙产品等级：C级 [Table 8] Hexagon head bolts, continuous thread, product grade C [Table 8]
27	[欧标] EN 24017 - 1991	六角头螺钉产品等级：A级和B级 Hexagon Head Screws - Product Grades A and B
28	[欧标] EN 24018 - 1991	六角头螺钉产品等级：C级 Hexagon Head Screws - Product Grade C
29	[意大利] UNI 5739 - 1965	六角头螺栓 Hexagon Head Bolts 供应商(1)
30	[意大利] UNI 6421 - 1969	全螺纹六角头螺栓 Hexagon screws for manufacture of railway and tramway rolling stock - ISO metric coarse thread - Finish A
31	[法国] NF E 25-114 - 2001	A级和B级六角头螺栓 Hexagon Head Bolts - Product Grades A And B
32	[法国] NF E 25-115-2 - 2001	C级全螺纹六角头螺钉 Hexagon Head Screws - Full Thread - Product Grade C
33	[英标] BS 4190 - 2014	六角头粗制螺钉 - 仅支承面车削 [Table 6] Iso Metric Hexagon Head Screws Faced Under Head Only [Table 6]
34	[英标] BS 4190 - 2014	六角头粗制螺钉 [Table 5] Iso Metric Black Hexagon Head Screws [Table 5]
35	[英标] BS 4190 - 2001	六角头粗制螺钉 - 仅支承面车削 [Table 11] Iso Metric Hexagon Head Screws Faced Under Head Only [Table 11]
36	[英标] BS 4190 - 2001	六角头粗制螺钉 [Table 10] Iso Metric Black Hexagon Head Screws [Table 10]
37	[英标] BS 1981 - 1991	六角头机械螺钉 Table 16 Hexagon Head Screws
38	[英标] BS 1083 - 1965	精制六角头螺钉, 垫圈面, 全牙 - B.S.W. & B.S.F.英制螺纹 Precision Hexagon Head Screws - Washer Faced - B.S.W. & B.S.F. threads
39	[英标] BS 1768 - 1963	精制美制六角头螺钉 Unified Hexagon Head Screws, Washer Faced
40	[英标] BS 916 - 1953	英制六角头全螺纹螺钉 - 粗制 - 镦锻 [Table 1] Hexagon Head Screws with B.S.Threads [Table 1]
41	[英标] BS 916 - 1953	英制六角头全螺纹螺钉 - 粗制 - 车削支承面 [Table 2] Hexagon screws faced under head with B.S.Threads - Black [Table 2]
42	[英标] BS 1769 - 1951	大六角头螺钉(统一螺纹) Unified Hexagon Head Screws - heavy series
43	[澳标] AS 1110.2 - 2000	米制六角头螺钉 A和B级 ISO Metric Hexagon Head Screws - Product Grades A And B
44	[澳标] AS 1111.2 - 2000	米制六角头螺钉 C级 ISO Metric Hexagon Head Screws - Product Grade C
45	[澳标] AS /NZS 2465 - 1999 (R2016)	美制六角螺钉 - UNC, UNF螺纹 Hexagon Screws (UNC and UNF threads)
46	[澳标] AS /NZS 2451 - 1998	英制螺纹六角头螺钉 Screws with British Standard Whitworth Threads (rationalized series)
47	[澳标] AS /NZS 1427 - 1996	米制凹穴六角头机械螺钉 [Table 6] ISO metric indented hexagon head screws [Table 6]
48	[台湾] CNS 3122 - 2001	全螺纹六角头螺栓 Hexagon Bolts With Thread Up To Head, Finished And Semi-Finished
49	[台湾] CNS 4322 - 1982	粗制全螺纹六角头螺栓 Hexagon Bolts With Thread Approximately To Head, Regular
50	[俄标] GOST P ISO 4017 - 2013	六角头螺栓 A级和B级 Hexagon head screws - Product grades A and B
51	[俄标] GOST 50792 - 1995	六角头螺钉产品等级C Hexagon Head Screws - Product Grade C
52	[俄标] GOST R 50793 - 1995	六角头全螺纹螺钉——产品等级 A 级, B 级 Hexagon Head Screws with Threading Up To Head, Product Grades A and B
53	[韩标] KS B 1002 (T5) - 2001	A级全螺纹六角头螺栓 Table 5 Hexagon Head Bolts-Full Thread - Grade A [Table 5]
54	[韩标] KS B 1002 (T6) - 2001	B级全螺纹六角头螺栓 Table 6 Hexagon Head Bolts-Full Thread - Grade B [Table 6]
55	[韩标] KS B 1002 (T7) - 2001	C级全螺纹六角头螺栓 Table 7 Hexagon Head Bolts-Full Thread - Grade C [Table 7]
56	[德标] DIN EN 24017 - 1992	六角头螺钉产品等级 A和B Hexagon Head Screws Product Grades A and B
57	[德标] DIN EN ISO 4017 - 2014	六角头螺栓（全螺纹）— A级 / B级 Hexagon Head Screws — Product Grades A and B 供应商(14)
58	[德标] DIN EN ISO 4017 - 2001	六角头螺栓（全螺纹）— A级 B级 Hexagon head screws — Product grades A and B 供应商(14)
59	[德标] DIN EN ISO 4018 - 2011	六角头全螺纹螺钉——产品等级 C 级 Hexagon Head Screws - Product Grade C
60	[印标] IS 1363 (-2) - 2002	C级六角头全牙螺栓（M5-M64） Hexagon Head Screws (Size Range M5 to M64), Product Grade C
61	[印标] IS 1364 (-2) - 2002	六角头全牙螺栓（M1.6 - M64）A级 B级 Hexagon Head Screws (Size Range M1.6 - M64)
62	[航天] QJ 2581 (A) - 2011	钛合金六角头全螺纹螺栓 Hexagon head bolts with thread to head in titanium alloys
63	[航天] QJ 2581 - 1993	钛合金六角头全螺纹螺栓 Hexagon head bolts with thread to head in titanium alloys