会员中心 | English

头部带孔六角头螺栓 3型 GOST 7796 (-3) - 1970

选择规格尺寸点击↓

(14)

(18)

(22)

(27)

括号内尺寸为非优选

尺寸单位: mm

俄标GOST 7796 (-3) - 1970 GOST7796 7796GOS 头部带孔六角头螺栓 3型

扫一扫分享

公差公制螺纹极限尺寸米/英制螺纹对照螺纹直径与受力截面积最小破坏扭矩牌号等级毛坯直径

螺纹尺寸
d

(14)

(18)

(22)

(27)

P	螺距	粗牙
		细牙
d_s
s
k
e	最小值
d_w	最小值
c	最小值
	最大值
d₄	最小值=公称
	最大值
L₂	公称
	最小值
	最大值

1.25	1.5	1.75	2	2	2.5	2.5	2.5	3	3	3.5	4	4.5	5
1	1.25	1.25	1.5	1.5	1.5	1.5	1.5	2	2	2	3	3	3
8	10	12	14	16	18	20	22	24	27	30	36	42	48
12	14	17	19	22	24	27	30	32	36	41	50	60	70
5.3	6.4	7.5	8.8	10	12	12.5	14	15	17	18.7	22.5	26	30
13.1	15.3	18.7	20.9	23.9	26.2	29.6	33	35	39.6	45.2	55.4	66.4	76.9
10.5	12.5	15.5	17.2	20.1	22	24.8	27.7	29.5	33.2	38	46.6	55.9	64.7
0.15	0.15	0.15	0.15	0.2	0.2	0.2	0.2	0.2	0.2	0.2	0.2	0.25	0.25
0.6	0.6	0.6	0.6	0.8	0.8	0.8	0.8	0.8	0.8	0.8	0.8	0.8	0.8
2.5	2.5	3.2	3.2	4	4	4	4	4	4	4	5	5	5
2.9	2.9	3.68	3.68	4.48	4.48	4.48	4.48	4.48	4.48	4.48	5.48	5.48	5.48
2.8	3.5	4	4.5	5	6	6.5	7	7.5	8.5	9.5	11.5	13	15
2.6	3.26	3.76	4.26	4.76	5.76	6.21	6.71	7.21	8.21	9.21	11.15	12.65	14.65
3	3.74	4.24	4.74	5.24	6.24	6.79	7.29	7.79	8.79	9.79	11.85	13.35	15.35

引用参考

GB /T 1172 - 1999

黑色金属硬度及强度换算值

GB /T 5267.1 - 2002

镀锌、镀镍、镀镉、复合镀等层镀层盐雾腐蚀的防护性能

GB /T 193 - 2003

普通螺纹（一般用途米制螺纹）- 直径与螺距系列 (ISO 261: 1998, MOD)

GB /T 3106 - 2016

紧固件 - 螺栓、螺钉和螺柱 - 公称长度和螺纹长度 (ISO 888:2012, MOD)

GB /T 12603 - 2005

金属热处理工艺分类及代号

GB /T 3 - 1997

普通螺纹收尾、肩距、退刀槽和倒角 (ISO 3508:1976 / ISO 4755:1983)

GB /T 5779.1 - 2000

紧固件表面缺陷 - 螺栓、螺钉和螺柱 - 一般要求

GB /T 5779.3 - 2000

紧固件表面缺陷 - 螺栓、螺钉和螺柱 - 特殊要求

注：技术数据仅供参考，请以官方原件为准！

类似标准及供货信息

1	[国标] GB /T 32.1 - 2020	六角头头部带孔螺栓 Hexagon Bolts With Wire Holes On Head 供应商(8)
2	[国标] GB /T 32.3 - 2020	六角头头部带孔螺栓细牙 Hexagon Bolts With Wire Holes On Head - Fine Pitch Thread 供应商(1)
3	[国标] GB 32.1 - 1988	六角头头部带孔螺栓 A和B级 Hexagon Bolts With Wire Hole On Head-Product Grade A and B 供应商(8)
4	[国标] GB 32.2 - 1988	细杆 B级六角头头部带孔螺栓 Hexagon Bolts With Wire Holes On Head - Reduced Shank - Product Grade B 供应商(1)
5	[国标] GB 32.3 - 1988	六角头头部带孔螺栓细牙 A和B级 Hexagon Bolts With Wire Holes On Head-fine Pitch Thread-product Grade A And B 供应商(1)
6	[国标] GB 25 - 1976	小六角头部带孔螺栓 Bolts, Small Hexagon Head With Holes Through The Head 供应商(1)
7	[国标] GB 26 - 1976	小六角头头部带孔导颈螺栓 Bolts, Small Hexagon Head With Fit Neck And Holes Through The Head
8	[汽标代号] Q 170	六角头头部带孔螺栓 Hexagon bolts with wire holes on head
9	[汽标代号] Q 170B	六角头头部带孔螺栓 [粗牙普通螺纹] Hexagon bolts with wire hole on head
10	[汽标代号] Q 171	细牙六角头头部带孔螺栓 Hexagon bolts with wire holes on head
11	[汽标代号] Q 171B	六角头头部带孔螺栓 [细牙普通螺纹] Hexagon bolts with wire hole on head
12	[汽标代号] Q 171C	六角头头部带孔螺栓 [较细牙普通螺纹] Hexagon bolts with wire hole on head
13	[欧标] EN 2887 - 1995	航空航天 - 六角头螺栓全螺纹耐腐蚀钢钝化级别：600MPa (环境温度)/425℃ Aerospace series - Bolts, normal hexagonal head, threaded to head, in corrosion resisting steel, passivated - Classification: 600 MPa (at ambient temperature)/425 °C
14	[铁道部] TB /T 1479 - 1991	轨道车辆车轴轴端螺栓
15	[俄标] GOST 7798 - 1970	六角头头部带孔螺栓 Hexagon bolts with wire holes on head
16	[俄标] GOST 7805 (-3) - 1970	六角头头部带孔螺栓 3型 Hexagon Bolts With Wire Holes On Head, product grade A, Type 3
17	[美国航空航天] NAS NAM 51474 (DS 51474) - 2011	米制六角头全螺纹螺钉 Screw, cap, hex head, fully threaded, metric
18	[航天] QJ 2365 - 1992	六角头头部带孔螺栓 Hexagon head bolts with hole
19	[中国兵器工业总公司部标准] WJ 2215 - 1994	六角头头部带孔全螺纹螺栓 Hexagon Bolts With Wire Holes On Head - Full Thread