开槽和无槽六角凸缘头（垫圈头）螺钉 (ASTM F837, F468) ASME B 18.6.3 (H10A) - 2024
| 选择规格尺寸 点击↓ 2# 3# 4# 5# 6# 8# 10# 12# 1/4 5/16 3/8 7/16 1/2 |
尺寸单位:
inch |
|
|
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
|
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| ①,机械螺钉的螺纹长度： 1）螺纹规格≤5#: 公称长度≤3倍公称直径的应为满扣产品，头下螺纹肩距≤1倍螺距。 公称长度＞3倍公称直径到 1-1/8 in 的，允许头下肩距最大不超过2倍螺距。 若无其他规定，长螺钉的最小螺纹长度为1 in 。 2）螺纹规格≥6#: 公称长度≤3倍公称直径的应为满扣产品，头下螺纹肩距≤1倍螺距。 公称长度＞3倍公称直径到 2 in 的，允许头下螺纹肩距最大不超过2倍螺距。 若无其他规定，长螺钉最小螺纹长度为 1.5 in 。 ②,除非用户有要求，六角头凸缘螺钉不需要开槽。 ③,六角面与凸缘顶面结合处的圆角半径R应不大于螺钉公称直径的0.15倍。 ④,可选择凹穴型式。 ⑤,螺杆直径ds应不小于2A级螺纹最小中径，并不大于公称（基本）螺纹大径。 |
长度公差
Machine screws can be made to any length, but they are generally produced in fractional length increments of 1/16 in. for screws up to 5/8 in. long, 1/8 in. for screws over 5/8 in. through 1-1/2 in. long, and 1/4 in. for screws over 1-1/2 in. long.
标称螺钉尺寸的长度公差 | |||
标称螺钉长度 | 螺纹规格 | ||
0000~00 | 0~12 | 1/4~3/4 | |
≤1/2 | -0.01 | -0.02 | -0.03 |
＞1/2,≤1 | -0.02 | -0.03 | -0.03 |
＞1,≤2 | / | -0.06 | -0.06 |
＞2 | / | -0.09 | -0.09 |
类似标准及供货信息
| 1 |
![六角头凸缘（带垫）螺栓 1型 [Table JA.2]](http://img.164580.com/upload/48/pic/2023/11/17/1700201088392116642.jpg)
|
[日标] JIS B 1189 (Type 1) - 2014 |
六角头凸缘（带垫）螺栓 1型 [Table JA.2] Hexagon Bolt with flange (Collar) - Type 1 - [Table JA.2] 供应商(1) |
| 2 |
|
[日标] JIS B 1189 (Type 1) - 2005 |
六角头带垫螺栓 1型 Hexagon Flange with flat upper face Bolt - Type 1 [Attached Table 1] 供应商(1) |
| 3 |
|
[日标] JIS B 1189 (Class 1) - 1977 |
六角头垫圈面螺栓 1型 Hexagon bolts with collar - class 1 供应商(1) |
| 4 |
|
[法国] NF E 27-711 - 1982 |
六角凸缘螺栓 8.8级、10.9级 Hexagon Bolt with Collar |
| 5 |
|
[澳标] AS /NZS 1427 - 1996 |
米制小系列六角头带介螺栓 ISO metric small series hexagon washer head screws |
| 6 |
|
[美标] ASME B 18.6.3 (H10B-I) - 2024 |
十字槽六角凸缘头螺钉 Cross Recess Indented Hex Washer Head Screws |
| 7 |
|
[美标] ASME B 18.6.3 (H10B-VI) - 2024 |
梅花槽六角凸缘头螺钉 Recess Dimensions for Indented Hex Washer Head Screws，Type VI |
| 8 |
![开槽和无槽六角凸缘头（垫圈头）螺钉 [Table 32] (ASTM F837, F468)](http://img.164580.com/upload/48/pic/2023/11/17/1700200986084395472.jpg)
|
[美标] ASME B 18.6.3 (T32) - 2013 |
开槽和无槽六角凸缘头（垫圈头）螺钉 [Table 32] (ASTM F837, F468) Plain and Slotted Hex Washer Head Screws [Table 32] (ASTM F837, F468) |
| 9 |
|
[美标] ASME B 18.6.3 (T33-I) - 2013 |
十字槽六角凸缘头螺钉 Cross Recess Dimensions for Indented Hex Washer Head Screws |
| 10 |
|
[美标] ASME B 18.6.3 (T33-VI) - 2013 |
梅花槽六角凸缘头螺钉 Recess Dimensions for Indented Hex Washer Head Screws，Type VI |