index
logo

内螺纹圆柱销 ISO 8735 - 1987

选择规格尺寸 点击↓

Φ6

Φ8

Φ10

Φ12

Φ16

Φ20

Φ25

Φ30

Φ40

Φ50

ISO  8735 - 1987 内螺纹圆柱销

尺寸单位: mm
国际ISO 8735 - 1987 ISO8735 8735ISO 内螺纹圆柱销
ISO  8735 - 1987 内螺纹圆柱销
扫一扫分享
公称直径
d
Φ6 Φ8 Φ10 Φ12 Φ16 Φ20 Φ25 Φ30 Φ40 Φ50
d 最大值
最小值
a
c
d1
P 螺距
d2
t1
t2 最小值
t3
6.012 8.015 10.015 12.018 16.018 20.021 25.021 30.021 40.025 50.025
6.004 8.006 10.006 12.007 16.007 20.008 25.008 30.008 40.009 50.009
0.8 1 1.2 1.6 2 2.5 3 4 5 6.3
2.1 2.6 3 3.8 4.6 6 6 7 8 10
M4 M5 M6 M6 M8 M10 M16 M20 M20 M24
0.7 0.8 1 1 1.25 1.5 2 2.5 2.5 3
4.3 5.3 6.4 6.4 8.4 10.5 17 21 21 25
6 8 10 12 16 18 24 30 30 36
10 12 16 20 25 28 35 40 40 50
1 1.2 1.2 1.2 1.5 1.5 2 2 2.5 2.5
①,A 型一一球面圆柱端,适用于普通淬火钢和马氏体不锈钢
B 型一一平端,适用于表面淬火钢
替代列表
等效标准
国标 GB 国际 ISO 德标 DIN 欧标 EN
GB /T 120
ISO 8735
DIN EN ISO 8735
EN 28735
以上有部分标准可能为近似等效,如有异议以标准原件为准

技术条件和引用标准

材料
材料 -
-
-
表面处理
表面缺陷
验收及包装
说明
A型 B 型
化学成分, %
C:0.95~1.1
Si:0.15~0.35
Mn:0.25~0.4
P:0.03 max
S:0.025 max
Cr:1.35~1.65
硬度:550~650 HV 30
C:0.06~0.13
Si:0.1~0.4
Mn:0.25~0.6
P:0.025 max
S:0.05 max
C:0.15 max
Si:0.10max
Mn:0.9~1.3
P:0.07 max
S:0.15~0.35
Pb:0.15~0.35

由制造者确定
表面硬度: 600~700 HV1
渗碳层深度0.25~0. 4 mm 的硬度:
550 HV1 min
Plain, i.e. pins to be supplied in natural finish, treated with a protective lubricant, unless otherwise specified by agreement between customer and suppller.
Appropriate plating or coating processes should be employed to avoid hydrogen embrittlement. When pins are electroplated or phosphate-coated, they shall be suitably treated immediately after plating or coating to obviate detrimental hydrogen embrittlement.
Preferred coatings are chemical black oxide or non-electroltic zinc plating with chromate conversion coating ( see IS0 4520 ) .
其他表面镀层或表面处理,应由供需双方协议。
所有公差仅适用于涂、镀前的公差。
不允许有不规则的和有害的缺陷。
销的任何部位不得有毛刺
ISO 3269
①其他材料由供需双方协议。
注:技术数据仅供参考,请以官方原件为准!
告诉我在“易紧通”看到,将给您优惠
联系人:倪经理 点击这里给我发消息1583167904 点击这里给我发消息1935265021   移动电话: 17317454705(微信同号) Email: 登陆后可见
材质;轴承钢GCR15 规格范围:M4-24 表面处理:磨光,洗光,发黑,达克罗,久美特 本色 抛光
联系人:李国志 点击这里给我发消息364950872   移动电话: 15221513104     电话:021-67636815     微信号:15221513104 Email: 登陆后可见
材质:45#、Gcr15、轴承钢(硬度HRC58-62)、304、316;公称直径范围:3-50,公称长度范围:5-500mm 表面处理:磨光,洗光,发黑 ;现货供应,支持非标定制
类似标准及供货信息
1 不淬硬钢和奥氏体不锈钢内螺纹圆柱销 [国标]
GB /T 120.1 - 2000
不淬硬钢和奥氏体不锈钢内螺纹圆柱销
Parallel Pins With Internal Thread,Of Unhardened Steel And Austenitic Stainless Steel
供应商(10)
2 淬硬钢和马氏体不锈钢内螺纹圆柱销 [国标]
GB /T 120.2 - 2000
淬硬钢和马氏体不锈钢内螺纹圆柱销
Parallel Pins With Internal Thread,Of Hardened Steel And Martensitic Stainless Steel
供应商(10)
3 内螺纹圆柱销 [国标]
GB 120 - 1986
内螺纹圆柱销
Parallel Pins With Internal Thread
供应商(10)
4 内螺纹圆柱销 [德标]
DIN 7979 - 1977
内螺纹圆柱销
Parallel Pins With Internal Thread
供应商(5)
5 不淬硬钢和奥氏体不锈钢内螺纹圆柱销 [国际]
ISO 8733 - 1997
不淬硬钢和奥氏体不锈钢内螺纹圆柱销
Parallel Pins With Internal Thread, Of Unhardened Steel And Austenitic Stainless Steel
供应商(1)
6 淬硬钢和马氏体不锈钢内螺纹圆柱销 [国际]
ISO 8735 - 1997
淬硬钢和马氏体不锈钢内螺纹圆柱销
Parallel Pins With Internal Thread,Of Hardened Steel And Martensitic Stainless Steel
供应商(2)
7 不淬硬内螺纹圆柱销 [国际]
ISO 8733 - 1986
不淬硬内螺纹圆柱销
Parallel Pins With Internal Thread, Unhardened Steel And Austenitic Stainless Steel
供应商(1)
8 1型内螺纹圆柱销 Table 2 [日标]
JIS B 1359 - 2012
1型内螺纹圆柱销 Table 2
Parallel Pins With Internal Thread Of Class 1
9 2型内螺纹圆柱销 Table 3 [日标]
JIS B 1359 - 2012
2型内螺纹圆柱销 Table 3
Parallel Pins With Internal Thread Of Class 2
10 1型内螺纹圆柱销 [日标]
JIS B 1359 - 1990
1型内螺纹圆柱销
Parallel pins with internal thread
11 2型内螺纹圆柱销 [日标]
JIS B 1359 - 1990
2型内螺纹圆柱销
Parallel Pins With Internal Thread Of Class 2
12 淬硬内螺纹圆柱销 [欧标]
EN 28735 - 1992
淬硬内螺纹圆柱销
Hardened Parallel Pins with Internal Thread
13 不淬硬钢和奥氏体不锈钢内螺纹圆柱销 [法国]
NF E 25-755 - 1997 (R2005)
不淬硬钢和奥氏体不锈钢内螺纹圆柱销
Parallel Pins With Internal Thread,of Unhardened Steel And Austenitic Stainless Steel
14 淬硬钢和马氏体不锈钢内螺纹圆柱销 [法国]
NF E 25-757 - 1997 (R2002)
淬硬钢和马氏体不锈钢内螺纹圆柱销
Parallel Pins With Internal Thread, Of Hardened Steel And Martensitic Stainless Steel
15 内螺纹圆柱销 [台湾]
CNS 8779 - 1982
内螺纹圆柱销
Parallel Pins With Internal Thread
16 内螺纹圆柱销 淬硬 [韩标]
KS B 1309 - 2000 (R2020)
内螺纹圆柱销 淬硬
Parallel Pins With Internal Thread,of Hardened Steel And Martensitic Stainless Steel
17 内螺纹圆柱销 [德标]
DIN EN 28733 - 1992
内螺纹圆柱销
Parallel Pins With Internal Thread-Unhardened
供应商(5)
18 不淬硬钢和奥氏体不锈钢内螺纹圆柱销 [德标]
DIN EN ISO 8733 - 1998
不淬硬钢和奥氏体不锈钢内螺纹圆柱销
Parallel Pins With Internal Thread-Unhardened Steel And Austenitic Stainless Steel
供应商(5)
19 内螺纹圆柱销 [德标]
DIN EN ISO 8735 - 1998
内螺纹圆柱销
Parallel Pins with Internal Thread of Hardened Steel and Martensitic Stainless Steel
供应商(5)
© 易紧通 服务热线:4006-164580(免长途费)