会员中心 | English

十字槽半沉头螺钉 DIN 966 - 1990

选择规格尺寸点击↓

M1.6

M2.5

(M3.5)

M10

括号内尺寸为非优选

尺寸单位: mm

模型下载

模型下载替

扫一扫分享

单重计算公差公制螺纹极限尺寸米/英制螺纹对照螺纹直径与受力截面积最小破坏扭矩牌号等级毛坯直径

千件重及价格计算千件重 : kg x 元/kg = 元/千件

默认密度 g/cm³

螺纹尺寸
d

M1.6

M2.5

(M3.5)

M10

P	螺距
a	最大值
d_k	最大值=公称
d_k	最小值
f	≈
k	最大值
r	最大值
R	≈
x	最大值
槽号
M₁	≈
M₂	≈

0.35	0.4	0.45	0.5	0.6	0.7	0.8	1	1.25	1.5
0.7	0.8	0.9	1	1.2	1.4	1.6	2	2.5	3
3	3.8	4.7	5.6	6.5	7.5	9.2	11	14.5	18
2.75	3.5	4.4	5.3	6.14	7.14	8.84	10.57	14.07	17.57
0.4	0.5	0.6	0.75	0.9	1	1.25	1.5	2	2.5
0.96	1.2	1.5	1.65	1.93	2.2	2.5	3	4	5
0.4	0.5	0.7	0.8	0.95	1	1.3	1.6	2	2.5
3	4	5	6	7	8	10	12	16	20
0.9	1	1.1	1.25	1.5	1.75	2	2.5	3.2	3.8
0	1	1	1	2	2	2	3	4	4
1.9	2.5	2.7	3.1	4.2	4.5	5.3	6.8	9	10
1.8	2.4	2.8	3.1	4.3	4.6	5.3	7	8.8	9.9

千件钢制重≈kg

螺纹长度b

最小值

①,材料：
a)钢，强度等级(材料)：4.8,5.8,8.8. 标准DIN ISO 898-1
b)不锈钢，强度等级(材料)：A2-70，A4-70. 标准DIN 267-11
c)有色金属，强度等级(材料)：CuZn=铜锌合金，CU2或CU3由制造商选择。标准DIN 267-18
d)其他强度等级或材料或某种材料，例如 CU3，按协议

替代列表

DIN 966 - 1990 DIN EN ISO 7047 - 2011

等效标准

国标 GB	国际 ISO	德标 DIN
GB /T 820	ISO 7047	DIN EN ISO 7047

以上有部分标准可能为近似等效，如有异议以标准原件为准

技术条件和引用标准

材料

钢

不锈钢

有色金属

通用要求
螺纹	公差
	标准
机械性能	等级
	标准
公差	产品等级
	标准
表面处理	-
	-
表面粗糙度
表面缺陷
十字槽
验收及包装
备注

DIN 267 part 1
6g^①
DIN 13 part 13,15
4.8，5.8，8.8	A2-70，A4-70	CuZn = 铜锌合金 CU2或CU3由制造商选择
DIN ISO 898 part 1	DIN 267 part 11	DIN 267 part 18
A
DIN ISO 4759 part 1
不经处理 8.8：blackened （thermally or chemically）
电镀 DIN 267 part 9 其他表面处理由供需双方协议
DIN 267 part 2
DIN 267 part 19
DIN 7962
DIN 267 part 5
① Only for screws without surface protection. 6 g makes it possible for normal coating thicknesses to be applied in accordance with DIN 267 part 9, the reference line not being exceeded. Depending on the coating thickness required, a larger fundamental deviation shall be selected than that for the g position. This might, however, impair the resistance to stripping of the bolt / nut assembly.

引用参考

GB /T 1172 - 1999

黑色金属硬度及强度换算值

GB /T 5267.1 - 2002

镀锌、镀镍、镀镉、复合镀等层镀层盐雾腐蚀的防护性能

GB /T 193 - 2003

普通螺纹（一般用途米制螺纹）- 直径与螺距系列 (ISO 261: 1998, MOD)

GB /T 3106 - 2016

紧固件 - 螺栓、螺钉和螺柱 - 公称长度和螺纹长度 (ISO 888:2012, MOD)

GB /T 3 - 1997

普通螺纹收尾、肩距、退刀槽和倒角 (ISO 3508:1976 / ISO 4755:1983)

GB /T 5779.1 - 2000

紧固件表面缺陷 - 螺栓、螺钉和螺柱 - 一般要求

GB /T 5779.3 - 2000

紧固件表面缺陷 - 螺栓、螺钉和螺柱 - 特殊要求

注：技术数据仅供参考，请以官方原件为准！

告诉我在“易紧通”看到，将给您优惠

宁波欣昌金属制品有限公司

联系人：胡小姐

478963405 移动电话： 18668833133 电话：0574-62828345 Email:

登陆后可见

材料：302HQ, 304 (A2-70), 316C (A4-70, A4-80), 410, 430，公称直径：M3-M8，长度4-100mm

[询价]

惠州市昇沪汽车紧固件科技有限公司

联系人：黄俊辉

1540428407 移动电话： 13828802165 电话：0752-3951888, 3951820, 3951821, 3951825, 3951826 Email:

登陆后可见

材质：1008钢、1018#碳钢、Q235碳钢、35#合金钢、304HC不锈钢、316HC不锈钢，表面处理：环保彩锌、环保蓝白锌、环保黑锌、环保镍、热镀锌、达克罗、以及非环保电镀，规格：齐全

[询价]

东台勃林邦五金科技有限公司

联系人：徐明光

278446734@qg.com 移动电话： 13305198373（徐明光）；15358251989（柳崇兴）电话：0515-85521989 Email:

登陆后可见

材质：304，316；规格范围：M2-M8；支持非标定制

[询价]

江苏博凡科精密五金科技有限公司

联系人：汤继勇移动电话： 15298892886/15262400870 电话：0516-86839568 Email:

登陆后可见

材质：不锈钢、碳钢；公称直径范围：M1-M14；公称长度范围：5-400mm

[询价]

告诉我在“易紧通”看到，将给您优惠

类似标准及供货信息

1	[国标] GB /T 820 - 2015	十字槽半沉头螺钉 Raised Countersunk Head Screws with Cross Recess 供应商(3)
2	[国标] GB /T 820 - 2000	十字槽半沉头螺钉 Raised Countersunk Head Screws (Common Head Style) with Cross Recess 供应商(3)
3	[国标] GB /T 13806.1 (C) - 1992	精密机械用紧固件十字槽半沉头螺钉 Cross Recessed Raised Countersunk Head Screws For Fine Mechanics 供应商(1)
4	[国标] GB 820 - 1985	十字槽半沉头螺钉 Cross recessed raised countersunk head screws 供应商(3)
5	[国标] GB 974 - 1976	120°十字槽半沉头螺钉 120°Cross recessed raised countersunk screws
6	[德标] DIN 6929 (NE) - 2013	粗牙十字槽半沉头细杆螺钉 Raised Countersunk Head Screws
7	[国际] ISO 7047 - 2011	十字槽半沉头螺钉 Rasied Countersunk Head Screws(Common Head Style) ，Grade A 供应商(1)
8	[国际] ISO 7047 - 1994	十字槽半沉头螺钉 Countersunk Rasied Head Screws(Common Head Style) With Type H Or Type Z Cross Recess - Product Grade A 供应商(1)
9	[日标] JIS B 1111 (T12) - 2017	十字槽半沉头螺钉 [表12] Cross Recessed Raised Countersunk Head Screws [Table 12]
10	[日标] JIS B 1111 (JA5) - 2017	十字槽半沉头螺钉 [附属表 JA.5] Cross Recessed Raised Countersunk Head Screws
11	[日标] JIS B 1111 (T4) - 2006	十字槽半沉头螺钉 [表4] Cross Recessed Raised Countersunk Head Screws [table 4]
12	[日标] JIS B 1111 (T4) - 1996	十字槽半沉头螺钉 [表4] Cross Recessed Raised Countersunk Head Screws [table 4]
13	[日标] JIS B 1119 (2PC) - 1986	眼镜框架用 - 十一字槽盘形半沉头螺钉 Spectacle Frames - Cross-recessed Slotted Pan Countersunk Machine Screws
14	[汽标代号] Q 256	十字槽半沉头螺钉 Cross recessed raised countersunk head screws
15	[美标] ASME/ANSI B 18.6.3 (T8) - 2010	80°十字槽半沉头螺钉Table8 80° Cross recessed raised countersunk head screws
16	[美标] ASME/ANSI B 18.6.7M - 1998	米制十字槽半沉头螺钉Table7 Metric cross recessed raised countersunk screws
17	[美标] ASME/ANSI B 18.6.7M - 1998	米制米字槽半沉头螺钉Table8 Metric PZ drives raised countersunk head screws
18	[法国] NF E 25-120 - 1994	十字槽半沉头螺钉 Cross Recessed Raised Countersunk Head Screws, With Type H Or Type Z Cross Recessed - Product Grade A
19	[英标] BS 1981 - 1991	米字槽半沉头螺钉（短的）Table10 Recessed Raised Countersunk Head Machine Screws: Short Length
20	[英标] BS 1981 - 1991	米字槽半沉头螺钉Table8 Recessed raised Countersunk Head Machine Screws
21	[英标] BS 450 - 1958	英制十字槽半沉头螺钉 - B.S.W. & B.S.F. 螺纹 [Table 3] Recessed 90° Raised-Countersunk Head Screws with B.S.W. & B.S.F. Threads [Table 3]
22	[澳标] AS /NZS 1427 - 1996	米制十字槽半沉头螺钉 [Table 2] ISO metric cross-recess raised countersunk screws [Table 2]
23	[台湾] CNS 4561 - 1981	十字槽半沉头螺钉 Cross Recessed Raised Countersunk Head Screws
24	[俄标] GOST 17474 - 1980	十字槽半沉头螺钉 A级和B级 Raised countersunk head screws (Cross Recessed), product grades A and B
25	[韩标] KS B 1023 (T9) - 2016 (R2021)	十字槽半沉头螺钉 Cross Recessed Raised Countersunk Head Screws
26	[韩标] KS B 1023 (T4) - 2001	十字槽半沉头螺钉 Cross Recessed Raised Countersunk Head Screws
27	[德标] DIN EN ISO 7047 - 2011	H型或Z型十字槽半沉头螺钉（通用头型）- 产品等级A级 Raised Countersunk Head Screws (Common Head Style) with Type H or Type Z Cross Recess - Product Grade A 供应商(4)
28	[美标] ASME B 18.6.3 (H2B-I/H2B-IA) - 2024	十字槽半沉头螺钉 I和IA型 Cross Recessed Raised Countersunk Head Screws - Type I and IA
29	[美标] ASME B 18.6.3 (H3D-I/H3D-IA) - 2024	十字槽82°半沉头清根螺钉 Undercut Oval 82-deg Countersunk Head Screws, Type I & Type IA Recess
30	[美标] ASME B 18.6.3 (H4C) - 2024	82°小半沉头十字槽螺钉 (ASTM F837 / F468) Oval 82-deg Countersunk Trim Head Screws (ASTM F837 / F468)
31	[美标] ASME B 18.6.3 (T15) - 2013	82°小半沉头十字槽螺钉 [Table 15] (ASTM F837 / F468) Oval 82-deg Countersunk Trim Head Screws [Table 15] (ASTM F837 / F468)
32	[美标] ASME B 18.6.3 (T12-I/T12-IA) - 2013	十字槽82°半沉头清根螺钉 Undercut Oval 82-deg Countersunk Head Screws, Type I & Type IA Recess
33	[美标] ASME B 18.6.3 (T8-I/T8-IA) - 2013	十字槽半沉头螺钉 I和IA型【表7&8】 Cross recessed raised countersunk head screws - Type I and IA [Table 7&8]
34	[航天] QJ 2378 - 1992	十字槽半沉头螺钉 Countersunk raised head screws with cross recess

十字槽半沉头螺钉 DIN 966 - 1990

相关材料标准或牌号

技术条件和引用标准

引用参考