会员中心 | English

8.8 级、不锈钢及有色金属十字槽沉头螺钉 DIN EN ISO 7046-2 - 2011

选择规格尺寸点击↓

M2.5

(M3.5)

M10

括号内尺寸为非优选

DIN EN ISO 7046-2 - 2011 8.8 级、不锈钢及有色金属十字槽沉头螺钉

尺寸单位: mm

德标DIN EN ISO 7046-2 - 2011 DIN EN ISO704 8.8 级、不锈钢及有色金属十字槽沉头螺钉

模型下载替

模型下载

扫一扫分享

单重计算公差公制螺纹极限尺寸米/英制螺纹对照螺纹直径与受力截面积最小破坏扭矩牌号等级毛坯直径

千件重及价格计算千件重 : kg x 元/kg = 元/千件

默认密度 g/cm³

螺纹尺寸
d

M2.5

(M3.5)

M10

P	螺距
b	最小值
d_k	理论	最大值
	实际	最大值
		最小值
k	最大值
x	最大值
r	最大值
槽号
M₁	系列1 /H型
深度	系列1 /H型	最小值
		最大值
M₂	系列1 /Z型
深度	系列1 /Z型	最小值
		最大值
M₁	系列2 /H型
深度	系列2 /H型	最小值
		最大值
M₂	系列2 /Z型
深度	系列2 /Z型	最小值
		最大值

0.4	0.45	0.5	0.6	0.7	0.8	1	1.25	1.5
25	25	25	38	38	38	38	38	38
4.4	5.5	6.3	8.2	9.4	10.4	12.6	17.3	20
3.8	4.7	5.5	7.30	8.40	9.30	11.30	15.80	18.30
3.5	4.4	5.2	6.9	8	8.9	10.9	15.4	17.8
1.2	1.5	1.65	2.35	2.7	2.7	3.3	4.65	5
1	1.1	1.25	1.5	1.75	2	2.5	3.2	3.8
0.5	0.6	0.8	0.9	1	1.3	1.5	2	2.5
0	1	1	2	2	2	3	4	4
1.9	2.9	3.2	4.4	4.6	5.2	6.8	8.9	10
0.9	1.4	1.7	1.9	2.1	2.7	3	4	5.1
1.2	1.8	2.1	2.4	2.6	3.2	3.5	4.6	5.7
1.9	2.8	3	4.1	4.4	4.9	6.6	8.8	9.8
0.95	1.48	1.76	1.75	2.06	2.6	3	4.15	5.19
1.2	1.73	2.01	2.2	2.51	3.05	3.45	4.6	5.64
1.9	2.7	2.9	4.1	4.6	4.8	6.6	8.7	9.6
0.9	1.25	1.4	1.6	2.1	2.3	2.8	3.9	4.8
1.2	1.55	1.8	2.1	2.6	2.8	3.3	4.4	5.3
1.9	2.5	2.8	4	4.4	4.6	6.3	8.5	9.4
0.95	1.22	1.48	1.61	2.06	2.27	2.73	3.87	4.78
1.2	1.47	1.73	2.05	2.51	2.72	3.18	4.32	5.23

千件钢制重≈kg

①,系列1：a_max = 2.5P；系列2：a_max = 2P
②,材料：
a)钢，强度等级：8.8。标准ISO 898-1
b)不锈钢，强度等级：A2-70。标准ISO 3506-1
c)有色金属，性能等级：CU2，CU3（由制造商选择）。标准ISO 8839

替代列表

DIN 965 - 1990 DIN EN ISO 7046-2 - 2011

等效标准

国标 GB	国际 ISO	德标 DIN	法国 NF
GB /T 819.2	ISO 7046-2	DIN EN ISO 7046-2	NF E 25-119-2

以上有部分标准可能为近似等效，如有异议以标准原件为准

采用标准

ISO 7046 (-2) - 2011

8.8 级、不锈钢及有色金属十字槽沉头螺钉

技术条件和引用标准

材料

钢

不锈钢

有色金属

螺纹	公差
	标准
机械性能	性能等级
	标准
公差	产品等级
	标准
十字槽
表面处理	-
	-
表面缺陷
验收及包装

6 g
ISO 261，ISO 965-2
8.8	A 2-70	CU2、CU3（由制造者选择）
ISO 898-1	ISO 3506-1	ISO 8839
A
ISO 4759-1
ISO 4757
不经处理；电镀技术要求按 ISO 4042; 非电解锌片涂层技术要求按 ISO 10683	不经处理；钝化处理技术要求按 ISO 16048	不经处理；电镀技术要求按 ISO 4042
如需其他技术要求或表面处理，应由供需协议
ISO 6157-1、ISO 6157-3
ISO 3269

引用参考

GB /T 1172 - 1999

黑色金属硬度及强度换算值

GB /T 5267.1 - 2002

镀锌、镀镍、镀镉、复合镀等层镀层盐雾腐蚀的防护性能

GB /T 193 - 2003

普通螺纹（一般用途米制螺纹）- 直径与螺距系列 (ISO 261: 1998, MOD)

GB /T 3106 - 2016

紧固件 - 螺栓、螺钉和螺柱 - 公称长度和螺纹长度 (ISO 888:2012, MOD)

GB /T 3 - 1997

普通螺纹收尾、肩距、退刀槽和倒角 (ISO 3508:1976 / ISO 4755:1983)

GB /T 5779.1 - 2000

紧固件表面缺陷 - 螺栓、螺钉和螺柱 - 一般要求

GB /T 5779.3 - 2000

紧固件表面缺陷 - 螺栓、螺钉和螺柱 - 特殊要求

注：技术数据仅供参考，请以官方原件为准！

告诉我在“易紧通”看到，将给您优惠

宁波欣昌金属制品有限公司

联系人：胡小姐

478963405 移动电话： 18668833133 电话：0574-62828345 Email:

登陆后可见

材料：302HQ, 304 (A2-70), 316C (A4-70, A4-80), 410, 430，表面处理：本身，公称直径：M2.5~M8, #4-1/4，公称长度：5~100mm

[询价]

苏州永创紧固件厂

联系人：汤继勇

546348066 移动电话： 15298892886 电话：0512-66700967 Email:

登陆后可见

材质：不锈钢、碳钢；公称直径范围：M1-M14；公称长度范围：5-400mm

[询价]

苏州市桂丰精密不锈钢紧固件厂

联系人：杨钦移动电话： 15162465399 电话：0512-65808790 Email:

登陆后可见

材料：碳钢、不锈钢，表面处理：本色; 公称直径：M1.2-M8,公称长度：3mm-80mm

[询价]

余姚市鸿特盛金属制品有限公司

联系人：马华珍/徐天阳移动电话： 13095941973, 18268663653 电话：0574-62761228 Email:

登陆后可见

材料：不锈钢A2-70，A2-80，A4-70，A4-80，A2（302,303,304），A4(316)，410，430 公称范围：规格齐全

[询价]

惠州市昇沪汽车紧固件科技有限公司

联系人：黄俊辉

1540428407 移动电话： 13828802165 电话：0752-3951888, 3951820, 3951821, 3951825, 3951826 Email:

登陆后可见

材质：1008钢、1018#碳钢、Q235碳钢、35#合金钢、304HC不锈钢、316HC不锈钢，表面处理：环保彩锌、环保蓝白锌、环保黑锌、环保镍、热镀锌、达克罗、以及非环保电镀，规格：齐全

[询价]

告诉我在“易紧通”看到，将给您优惠

类似标准及供货信息

1	[国标] GB /T 819.1 - 2016	十字槽沉头螺钉第1部分：4.8级 Countersunk Flat Head Screws (Common Head Style) with Cross Recess - Part 1: Property Class 4.8 供应商(13)
2	[国标] GB /T 819.2 - 2016	十字槽沉头螺钉第2部分：8.8级、不锈钢及有色金属螺钉 Countersunk Flat Head Screws with Cross Recess - Part 2: Property Class 8.8, Stainless Steel Screws and Non-ferrous Metal Screws 供应商(1)
3	[国标] GB /T 819.1 - 2000	十字槽沉头螺钉 4.8级 Countersunk Flat Head Screws (Common Head Style) with Cross Recess - Part 1: Property Class 4.8 供应商(13)
4	[国标] GB /T 819.2 - 1997	十字槽沉头螺钉第2部分：钢8.8级、不锈钢A2-70和有色金属螺钉CU2或CU3 Cross Recessed Countersunk Flat Head Screws (Common Head Style) - Grade A - Part 2: Steel of Property Class 8.8, Stainless and Non-Ferrous Metals 供应商(1)
5	[国标] GB /T 13806.1 (B) - 1992	精密机械用紧固件十字槽沉头螺钉 Cross Recessed Countersunk Screws For Fine Mechanics 供应商(1)
6	[国标] GB 819 - 1985	十字槽沉头螺钉 Cross Recessed Countersunk Head Screws 供应商(13)
7	[国标] GB 819 - 1976	十字槽沉头螺钉 Cross recessed countersunk head screws 供应商(13)
8	[德标] DIN 965 - 1990	十字槽沉头螺钉 Cross Recessed Countersunk Head Screws 供应商(6)
9	[德标] DIN 34811 - 1999	塑料米字槽沉头螺钉 Plastic Flat Head Screws With Cross Recess
10	[国际] ISO 7046 (-2) - 2011	8.8 级、不锈钢及有色金属十字槽沉头螺钉 Countersunk Flat Head Screws(Common Head Style) With Type H Or Type Z Cross Recess-Product Grade A-Property Class 8.8 供应商(1)
11	[国际] ISO 7046-2 - 1990	8.8 级、不锈钢及有色金属十字槽沉头螺钉 Cross Recessed Countersunk Flat Head Screws(common Head Style) - Grade A - Steel Of Property Class 8.8,stainless Steel And Nonferrous Metals 供应商(1)
12	[国际] ISO 7046 (-1) - 2011	4.8级十字槽沉头螺钉 Countersunk Flat Head Screws(Common Head Style)With Type H Or Type Z Cross Recess- Product Grade A-Steel Screws Of Property Class 4.8
13	[国际] ISO 5856 - 2008	航空航天强度≤1100Mpa 金属材料标准杆短或中等长度MJ螺纹偏十字槽 100°沉头螺钉 Aerospace - Screws, 100 degrees normal countersunk head, internal offset cruciform ribbed or unribbed drive, normal shank, short or medium length MJ threads, metallic material, coated or uncoated, strength classes less than or equal to 1 100 MPa - Dimensi
14	[国际] ISO 7046-1 - 1994	十字槽沉头螺钉 Cross recessed countersunk head screws
15	[日标] JIS B 1111 (JA4) - 2017	十字槽沉头螺钉 [附属表 JA.4] Cross Recessed Countersunk Head Screws 供应商(2)
16	[日标] JIS B 1111 (T6) - 2017	十字槽沉头螺钉 4.8级 [表6] Cross Recessed Countersunk Head Screws - Class 4.8
17	[日标] JIS B 1111 (T9) - 2017	十字槽沉头螺钉 8.8级 [表9] Cross Recessed Countersunk Head Screws - Class 8.8
18	[日标] JIS B 1111 (T2) - 2006	十字槽沉头螺钉 4.8级 [表2] Cross Recessed Countersunk Head Screws - Class 4.8
19	[日标] JIS B 1111 (T3) - 2006	十字槽沉头螺钉 8.8级 [表3] Cross Recessed Countersunk Head Screws - Class 8.8
20	[日标] JIS B 1111 (T3) - 1996	十字槽沉头螺钉 8.8级 [表3] Cross recessed countersunk head screws - Class 8.8
21	[日标] JIS B 1111 (T2) - 1996	十字槽沉头螺钉 4.8级 [表2] Cross recessed countersunk head screws-Class 4.8
22	[汽标代号] Q 254	十字槽沉头螺钉 Cross recessed countersunk head screws
23	[美标] ASME/ANSI B 18.6.3 - 2010	十字槽沉头螺钉Table2 Cross recessed countersunk head screws 供应商(2)
24	[美标] ASME/ANSI B 18.6.7M - 1998	米制十字槽沉头螺钉Table3 Metric cross recessed countersunk screws
25	[美标] ASME/ANSI B 18.6.7M - 1998	米制米字槽沉头螺钉Table4 Metric PZ Drives countersunk head screws
26	[欧标] EN 4162 - 2016	航空航天 - 100°沉头螺钉偏十字槽镀镉合金钢中等螺纹长度粗公差普通杆等级：1100MPa(室温)/235℃ Aerospace Series - Screws, 100° Countersunk Normal Head, Offset Cruciform Recess, Coarse Tolerance Normal Shank, Medium Length Thread, in Alloy Steel, Cadmium Plated - 1100 MPa (at Ambient Temperature)/235 °C
27	[欧标] EN 2940 - 1995	航空航天系列镀银FE-PA92HT(A286)耐热钢制全螺纹偏置十字凹槽100°沉头螺钉等级:900MPa(环境温度)/650 Aerospace series - Screws, 100° countersunk head, offset cruciform recess, threaded to head, in heat resisting steel FE-PA92HT (A286), silver plated - Classification: 900 MPa (at ambient temperature)/650 °C
28	[意大利] UNI 7688 - 1977	十字槽沉头螺钉 Cross Recessed Countersunk Head Screws
29	[法国] NF E 25-119-1 - 1994	4.8级十字槽沉头螺钉 Countesunk Flat Head Screws,with Type H Or Type Z Cross Recessed - Product Grade A, Class 4.8
30	[法国] NF E 25-119-2 - 1994	8.8级十字槽沉头螺钉 Cross Recessed Countersunk Head Screws - Grade A, Class 8.8
31	[英标] BS 1981 - 1991	米字槽沉头螺钉（短的）Table 7 Recessed Truncated Countersunk Head Screws:short Length
32	[英标] BS 1981 - 1991	米字槽沉头螺钉Table4 Recessed Truncated Countersunk Head Screws: Long Length
33	[英标] BS 450 - 1958	英制十字槽沉头螺钉 - B.S.W. & B.S.F. 螺纹 [Table 2] Cross Recessed 90° Countersunk Head Screws with B.S.W. & B.S.F. Threads [Table 2]
34	[澳标] AS /NZS 1427 - 1996	米制十字槽沉头螺钉 [Table 1] ISO metric cross-recess countersunk screws [Table 1]
35	[台湾] CNS 4560 - 1981	十字槽沉头螺钉 Cross Recessed Countersunk Head Screws
36	[俄标] GOST 17475 - 1980	十字槽沉头螺钉 A级和B级 Countersunk head screws of accuracy classes A and B (Cross Recessed)
37	[韩标] KS B 1023 (T7) - 2016 (R2021)	4.8级十字槽沉头螺钉 Cross Recessed Countersunk Head Screws - Class 4.8
38	[韩标] KS B 1023 (T8) - 2016 (R2021)	8.8级及有色金属十字槽沉头螺钉 Non-ferrous Metal Cross Recessed Countersunk Head Screws - Class 8.8
39	[韩标] KS B 1023 (T2) - 2001	4.8级十字槽沉头螺钉 Cross Recessed Countersunk Head Screws - Class 4.8
40	[韩标] KS B 1023 (T3) - 2001	8.8级及有色金属十字槽沉头螺钉 Non-ferrous Metal Cross Recessed Countersunk Head Screws - Class 8.8
41	[德标] DIN EN ISO 7046-1 - 2011	十字槽沉头螺钉（通用头型）- 4.8级，钢制，产品等级A级 Countersunk Flat Head Screws (Common Head Style) with Type H or Type Z Cross Recess - Product Grade A - Part 1: Steel Screws of Property Class 4.8 供应商(6)
42	[军标] GJB 3371 (/57~/60) - 1998	十字槽100°沉头螺栓 Cross Recessed 100° Countersunk Head Screws
43	[军标] GJB 3371 (/62) - 1998	光杆公差带f9 十字槽100°沉头螺栓 Cross Recessed 100° Countersunk Head Screws，Shank Tolerance f9
44	[军标] GJB 3371 (/64) - 1998	光杆公差带h8短螺纹十字槽 100°沉头螺栓 Cross Recessed 100° Countersunk Head Screws, Short Thread, Shank Tolerance h8
45	[军标] GJB 3371 (/68) - 1998	十字槽 100°锥端沉头螺栓 Cross Recessed 100° Countersunk Head Screws With Cone Point
46	[军标] GJB 3371 (/84) - 1998	光杆公差带r6短螺纹十字槽 100°沉头螺栓 Cross Recessed 100° Countersunk Head Screws, Short Thread, Shank Tolerance r6
47	[军标] GJB 3372 (/45~/48) - 1998	十字槽100°沉头螺钉 Cross Recessed 100° Countersunk Head Screws
48	[军标] GJB 3372 (/49~/52) - 1998	十字槽100°小沉头螺钉 Cross recessed 100 ° small countersunk head screw
49	[印标] IS 7485 (-1) - 2005	H型或Z型十字槽沉头螺钉（普通头）产品等级A Countersunk flat head screws (common head style) with type H or Type Z cross recess - product grade A
50	[印标] IS 7485 - 1985 (R2001)	十字槽沉头螺钉 Cross recessed Countersunk head screws
51	[波兰标] PN 82208	90°米字槽沉头螺钉 90° Cross Recess Countersunk Flat Head Screws
52	[美标] ASME B 18.6.3 (H1B-I/H1B-IA) - 2024	82°十字槽沉头螺钉 (ASTM F837, F468) 82° Cross Recessed Countersunk Head Screws (ASTM F837, F468) 供应商(2)
53	[美标] ASME B 18.6.3 (T2-I/T2-IA) - 2013	82°十字槽沉头螺钉 [Table 2] (ASTM F837, F468) 82° Cross Recessed Countersunk Head Screws [Table 2] (ASTM F837, F468) 供应商(2)
54	[美标] ASME B 18.6.3 (H1D-I/H1D-IA) - 2024	100°十字槽沉头螺钉 (ASTM F837, F468) 100° Cross Recessed Countersunk Head Screws (ASTM F837, F468)
55	[美标] ASME B 18.6.3 (H1F-I/H1F-IA) - 2024	精密100°沉头十字槽机械螺钉 Close Tolerance 100-deg Flat Countersunk Head Screws
56	[美标] ASME B 18.6.3 (H3B-I/H3B-IA) - 2024	十字槽82°沉头清根机械螺钉 Undercut 82-deg Flat Countersunk Head Screws，Type I and IA
57	[美标] ASME B 18.6.3 (H4A) - 2024	82°小沉头十字槽螺钉 (ASTM F837 / F468) 82° Flat Coutersunk Trim head Screws (ASTM F837 / F468)
58	[美标] ASME B 18.6.3 (T13) - 2013	82°小沉头十字槽螺钉 [Table 13] (ASTM F837 / F468) 82° Flat Coutersunk Trim head Screws [Table 13] (ASTM F837 / F468)
59	[美标] ASME B 18.6.3 (T4-I/T4-IA) - 2013	100°十字槽沉头螺钉 [Table 4] (ASTM F837, F468) 100° Cross Recessed Countersunk Head Screws [Table 4] (ASTM F837, F468)
60	[美标] ASME B 18.6.3 (T6-I/T6-IA) - 2013	100°十字槽沉头精整螺钉 Close Tolerance 100-deg Flat Countersunk Head Screws (Machine Screws Only)
61	[美标] ASME B 18.6.3 (T10-I/T10-IA) - 2013	十字槽82°沉头清根机械螺钉 Undercut 82-deg Flat Countersunk Head Screws，Type I and IA
62	[航天] QJ 2584 (A) - 2011	钛合金十字槽沉头螺钉 Countersunk Head Screws With Cross Recess in Titanium Alloys
63	[航天] QJ 2584 - 1993	钛合金十字槽沉头螺钉 Countersunk Head Screws With Cross Recess in Titanium Alloys
64	[航天] QJ 2377 - 1992	十字槽沉头螺钉 Cross recessed countersunk head screws
65	[航空] HB 1- 208 - 1995	十字槽120°沉头螺钉 Cross Recess 120° Countersunk Head Screw 供应商(1)
66	[航空] HB 1-206 - 2002	十字槽90°沉头螺钉 90° Countersunk Head Screw with Cross Recess
67	[航空] HB 7196~7199 (7196/7197/7198/7199) - 1995	十字槽100°沉头螺钉（带孔或不带孔） Cross Recessed 100° Countersunk Head Screws
68	[航空] HB 6565 - 1992	钛合金光杆公差带f9高扭矩十字槽100°沉头螺栓 Titanium alloy smooth rod tolerance zone f9 high torque cross groove 100° countersunk head bolt
69	[深圳紧固件行业协会标准] T/SZJGJ 001 (E) - 2024	十字槽沉头机器螺钉 Cross Recessed Countersunk Head Screws