会员中心 | English

十字槽盘头螺钉 UNI 7687

选择规格尺寸点击↓

M2.5

(M3.5)

M10

括号内尺寸为非优选

尺寸单位: mm

扫一扫分享

单重计算公差公制螺纹极限尺寸米/英制螺纹对照螺纹直径与受力截面积最小破坏扭矩牌号等级毛坯直径

千件重及价格计算千件重 : kg x 元/kg = 元/千件

默认密度 g/cm³

螺纹规格
d

M2.5

(M3.5)

M10

P	螺距
D	最小值
	最大值
k	最小值
	最大值
r₁	最小值
r₂	≈
V	≈
槽号
M₁	Pz型
深度	Pz型	最小值
		最大值
M₂	Ph型
深度	Ph型	最小值
		最大值

0.4	0.45	0.5	0.6	0.7	0.8	1	1.25	1.5
3.82	4.82	5.82	6.78	7.78	9.78	11.73	15.73	19.67
4	5	6	7	8	10	12	16	20
1.48	1.88	2.28	2.58	2.95	3.65	4.45	5.85	7.32
1.72	2.12	2.52	2.82	3.25	3.95	4.75	6.15	7.68
0.2	0.25	0.3	0.35	0.4	0.5	0.6	0.8	1
4	5	6	7	8	10	12	16	20
1.1	1.3	1.6	1.9	2	2.5	3	3.7	4.8
1	1	1	2	2	2	3	4	4
2.11	2.9	3.15	3.91	4.29	4.7	6.73	8.46	10
1.17	1.53	1.81	1.47	1.88	2.28	3.02	3.71	5.23
1.42	1.78	2.06	1.93	2.34	2.74	3.48	4.17	5.69
2.5	2.7	3.1	4.2	4.6	5.3	6.8	9	10.2
1.1	1.3	1.7	1.74	2.04	2.77	3.05	4.18	5.38
1.4	1.6	2	2.24	2.54	3.27	3.53	4.88	5.88

千件钢制重≈kg

替代列表

暂无

等效标准

国标 GB	国际 ISO	德标 DIN	意大利 UNI	法国 NF
GB /T 818	ISO 7045	DIN EN ISO 7045	UNI 7687	NF E 25-121

以上有部分标准可能为近似等效，如有异议以标准原件为准

引用参考

GB /T 1172 - 1999

黑色金属硬度及强度换算值

GB /T 5267.1 - 2002

镀锌、镀镍、镀镉、复合镀等层镀层盐雾腐蚀的防护性能

GB /T 193 - 2003

普通螺纹（一般用途米制螺纹）- 直径与螺距系列 (ISO 261: 1998, MOD)

GB /T 3106 - 2016

紧固件 - 螺栓、螺钉和螺柱 - 公称长度和螺纹长度 (ISO 888:2012, MOD)

GB /T 3 - 1997

普通螺纹收尾、肩距、退刀槽和倒角 (ISO 3508:1976 / ISO 4755:1983)

GB /T 5779.1 - 2000

紧固件表面缺陷 - 螺栓、螺钉和螺柱 - 一般要求

GB /T 5779.3 - 2000

紧固件表面缺陷 - 螺栓、螺钉和螺柱 - 特殊要求

注：技术数据仅供参考，请以官方原件为准！

类似标准及供货信息

1	[国标] GB /T 818 - 2016	十字槽盘头螺钉 Pan Head Screws with Cross Recess 供应商(14)
2	[国标] GB /T 823 - 2016	十字槽小盘头螺钉 Small Pan Head Screws with Cross Recess 供应商(4)
3	[国标] GB /T 818 - 2000	十字槽盘头螺钉 Pan Head Screws with Cross Recess 供应商(14)
4	[国标] GB 823 - 1988	十字槽小盘头螺钉 Cross Recessed Small Pan Head Screws 供应商(4)
5	[国标] GB 818 - 1985	十字槽盘头螺钉 Cross Recessed Pan Head Screws 供应商(14)
6	[国标] GB 818 - 1976	十字槽盘头螺钉 Cross Recessed Pan Head Screws 供应商(14)
7	[德标] DIN 967 - 2018	十字槽盘头凸缘螺钉 A级 Cross Recessed Pan Head Screws with Collar - Product Grade A 供应商(1)
8	[德标] DIN 967 - 2002	十字槽盘头凸缘螺钉 A级 Cross Recessed Pan Head Screws with Collar - Product Grade A 供应商(1)
9	[德标] DIN 7985 - 1990	十字槽球面(矮)圆柱头[盘头]螺钉 Cross Recessed Raised Cheese Head Screws 供应商(6)
10	[德标] DIN 6929 (CE) - 2013	粗牙十字槽盘头细杆螺钉 Pan Head Screws With Cross Recess
11	[国际] ISO 7045 - 2011	A级十字槽盘头螺钉 H型或Z型 Pan Head Screws With Type H Or Type Z Cross Recess-Product Grade A 供应商(3)
12	[国际] ISO 7045 - 1994	十字槽盘头螺钉 Pan head screws with type H or type Z cross recess- Product grade A 供应商(3)
13	[日标] JIS B 1111 (T3) - 2017	十字槽盘头螺钉 [表3] Cross Recessed Pan Head Screws 供应商(2)
14	[日标] JIS B 1111 (T1) - 2006	十字槽盘头螺钉 [表1] Cross Recessed Pan Head Screws 供应商(2)
15	[日标] JIS B 1111 (T1) - 1996	十字槽盘头螺钉 [表1] Cross recessed pan head screws 供应商(2)
16	[日标] JIS B 1111 (JA3) - 2017	十字槽盘头螺钉 [附属表 JA.3] Cross Recessed Pan Head Screws
17	[日标] JIS B 1111 (A1) - 2006	十字槽盘头螺钉 [附属表1] Cross Recessed Pan Head Screws
18	[日标] JIS B 1111 (A1) - 1996	十字槽盘头螺钉 [附属表1] Cross recessed pan head screws
19	[日标] JIS B 1119 (2P) - 1986	眼镜框架用 - 十一字槽盘头螺钉 Spectacle Frames - Cross-recessed Slotted Pan Head Machine Screws
20	[汽标代号] Q 214	十字槽盘头螺钉 Cross recessed pan head screws 供应商(1)
21	[美标] ASME/ANSI B 18.6.3 - 2010	十字槽盘头螺钉Table18 Cross recessed pan head machine screws 供应商(4)
22	[美标] ASME/ANSI B 18.6.7M - 1998	米制十字槽盘头螺钉Table11 Metric cross recessed pan head screws
23	[美标] ASME/ANSI B 18.6.7M - 1998	米制米字槽盘头螺钉Table12 Metric PZ Drives pan head screws
24	[欧标] EN 2884 - 2024	航天航空 - 盘头螺钉偏十字槽光杆公差h12 短螺纹钛合金阳极氧化 MoS2润滑 - 等级：1100MPa(室温)/315℃ Aerospace Series - Screws, Pan Head, Offset Cruciform Recess, Coarse Tolerance Normal Shank, Short Thread, in Titanium Alloy, Anodized, MoS2 Lubricated - Classification: 1100 MPa (at Ambient Temperature)/315℃
25	[欧标] EN 2884 - 1996	航天航空 - 盘头螺钉偏十字槽光杆公差h12 短螺纹钛合金阳极氧化 MoS2润滑 - 等级：1100MPa(室温)/315℃ Aerospace Series - Screws, Pan Head, Offset Cruciform Recess, Coarse Tolerance Normal Shank, Short Thread, in Titanium Alloy, Anodized, MoS2 Lubricated - Classification: 1100 MPa (at Ambient Temperature)/315℃
26	[欧标] EN 2897 - 1996	航天航空 - 盘头螺钉偏十字槽紧公差普通杆短螺纹合金镀镉 - 等级：1100MPa(室温)/235℃ Aerospace Series - Screws, Pan Head, Offset Cruciform Recess, Close Tolerance Normal Shank, Short Thread, in Alloy Steel, Cadmium Plated - Classification: 1100 MPa (at Ambient Temperature)/235℃
27	[法国] NF E 25-121 - 1994	十字槽盘头螺钉 Pan Head Screws With Type H Or Type Z Cross Recess - Product A
28	[英标] BS 1981 - 1991	米字槽盘头螺钉Table12 Cross Recessed Pan Head Machine Screws
29	[英标] BS 450 - 1958	英制十字槽盘头螺钉 - B.S.W. & B.S.F. 螺纹 [Table 5] Cross Recessed Pan Head Screws with B.S.W. & B.S.F. Threads [Table 5]
30	[澳标] AS /NZS 1427 - 1996	米制十字槽盘头螺钉 ISO metric cross-recess pan head screws
31	[原电子工业部] SJ 2828 - 1987	十字槽盘头螺钉 Cross recessed pan head screws
32	[台湾] CNS 9674 - 1988	十字槽盘头螺钉 Cross Recessed Pan Head Screws
33	[台湾] CNS 9677 - 1988	十字槽圆顶盘头螺钉 Corss Recessed Oval Pan Head Machine Screws
34	[韩标] KS B 1023 (T6) - 2016 (R2021)	十字槽盘头螺钉 Pan head screws with type H or type Z cross recess- Product grade A
35	[韩标] KS B 1023 (T1) - 2001	十字槽盘头螺钉 Cross Recessed Pan Head Screws
36	[德标] DIN EN ISO 7045 - 2011	十字槽盘头螺钉 - 产品等级A级 Pan Head Screws With Type H or Type Z Cross Recess- Product Grade A 供应商(6)
37	[印标] IS 7483 - 2005	十字槽盘头螺钉 A级 Pan Head Screws with Type H or Z Cross Recess - Product Grade A
38	[美标] ASME B 18.6.3 (H5B-I/H5C-IA) - 2024	十字槽盘头螺钉 (ASTM F837, F468) Type I Cross Recessed Pan Head Screws (ASTM F837, F468) 供应商(4)
39	[美标] ASME B 18.6.3 (T18-I/T19-IA) - 2013	十字槽盘头螺钉 [Table 18] (ASTM F837, F468) Dimensions of Type I Cross Recessed Pan Head Screws (ASTM F837, F468) 供应商(4)
40	[航天] QJ 2376 - 1992	十字槽盘头螺钉 Cross recessed pan head screws
41	[深圳紧固件行业协会标准] T/SZJGJ 001 (F) - 2024	十字槽盘头机器螺钉 Pan Head Screws With Cross Recess