index
会员中心 | English
logo
首页 产品与标准 ASME B 18.6.3 (T11t) - 2013 80° 开槽半沉头清根自攻螺钉 [Table 11]

80° 开槽半沉头清根自攻螺钉 [Table 11] ASME B 18.6.3 (T11t) - 2013

选择规格尺寸 点击↓

0#

1#

2#

3#

4#

5#

6#

7#

8#

10#

12#

1/4

5/16

3/8

7/16

1/2

ASME B 18.6.3 (T11t) - 2013 80° 开槽半沉头清根自攻螺钉 [Table 11]

尺寸单位: inch
美标ASME B18.6.3 (T11t) - 2013 ASME18.6.3 80° 开槽半沉头清根自攻螺钉 [Table 11]
ASME B 18.6.3 (T11t) - 2013 80° 开槽半沉头清根自攻螺钉 [Table 11]
扫一扫分享
单重计算 公差
螺纹尺寸
d
0# 1# 2# 3# 4# 5# 6# 7#
d 公称
PP
dk 最大值
最小值
k 参考值
f 参考值
n 最大值
最小值
t 最大值
最小值
α 最大值
最小值
L0 ① 公称
Y ① 螺纹过渡长度(全螺纹) 最大值
b ① 螺纹长度 (长螺钉) 最小值
0.0600 0.0730 0.0860 0.0990 0.1120 0.1250 0.1380 0.1510
48 42 32 28 24 20 20 19
0.112 0.137 0.162 0.187 0.212 0.237 0.262 0.287
0.096 0.120 0.144 0.167 0.191 0.215 0.238 0.262
0.025 0.031 0.036 0.042 0.047 0.053 0.059 0.064
0.021 0.025 0.029 0.033 0.037 0.041 0.045 0.049
0.023 0.026 0.031 0.035 0.039 0.043 0.048 0.048
0.016 0.019 0.023 0.027 0.031 0.035 0.039 0.039
0.028 0.034 0.040 0.047 0.053 0.059 0.065 0.071
0.022 0.027 0.033 0.038 0.043 0.048 0.053 0.059
82° 82° 82° 82° 82° 82° 82° 82°
80° 80° 80° 80° 80° 80° 80° 80°
7/16 9/16 5/8 3/4 13/16 15/16 1 1-1/8
0.021 0.024 0.031 0.036 0.042 0.050 0.050 0.053
0.360 0.440 0.520 0.590 0.670 0.750 0.830 0.910
螺纹尺寸
d
8# 10# 12# 1/4 5/16 3/8 7/16 1/2
d 公称
PP
dk 最大值
最小值
k 参考值
f 参考值
n 最大值
最小值
t 最大值
最小值
α 最大值
最小值
L0 ① 公称
Y ① 螺纹过渡长度(全螺纹) 最大值
b ① 螺纹长度 (长螺钉) 最小值
0.1640 0.1900 0.2160 0.2500 0.3125 0.3750 0.4375 0.5000
18 16 14 14 12 12 10 10
0.312 0.362 0.412 0.477 0.597 0.717 0.760 0.815
0.285 0.333 0.380 0.442 0.556 0.670 0.715 0.765
0.070 0.081 0.092 0.107 0.134 0.161 0.156 0.156
0.052 0.060 0.068 0.079 0.099 0.117 0.122 0.131
0.054 0.060 0.067 0.075 0.084 0.094 0.094 0.106
0.045 0.050 0.056 0.064 0.072 0.081 0.081 0.091
0.078 0.090 0.103 0.119 0.149 0.179 0.184 0.204
0.064 0.074 0.085 0.098 0.124 0.149 0.154 0.169
82° 82° 82° 82° 82° 82° 82° 82°
80° 80° 80° 80° 80° 80° 80° 80°
1-1/4 1-3/8 1-5/8 1-13/16 1-13/16 1-7/8 1-7/8 1-7/8
0.056 0.062 0.071 0.071 0.083 0.083 0.100 0.100
0.980 1.140 1.300 1.500 1.500 1.500 1.500 1.500
①,正常情况下，当螺钉长度小于等于其公称长度L0时应采用全螺纹，过渡螺纹长度应小于等于Y；若螺钉长度大于其公称长度L0可采用半牙型式，但其螺纹长度应不小于b。
替代列表
ASME B 18.6.3T11t - 2013 ASME B 18.6.3H3C+T1A - 2024

采用标准

工艺相关

ASME B 18.6.3 (T11) - 2013
82° 开槽半沉头清根机械螺钉 [table 11] (ASTM F837 / F468)
ASME B 18.6.3 (T12-I/T12-IA) - 2013
十字槽82°半沉头清根螺钉
ASME B 18.6.3 (T12-I/T12-IA+T40) - 2013
十字槽82°半沉头清根AB ABR自攻螺钉
ASME B 18.6.3 (T12-III) - 2013
方槽82°半沉头清根螺钉
ASME B 18.6.3 (T12-III+T40) - 2013
四方槽82°半沉头清根 AB ABR自攻螺钉
ASME B 18.6.3 (T7+T40) - 2013
82°开槽半沉头 AB ABR 自攻螺钉 [Table 7]

自攻螺纹：

1 AB型和ABR型自攻螺纹和末端 [Table 40] [美标]
ASME/ANSI B 18.6.3 (T40) - 2013		 AB型和ABR型自攻螺纹和末端 [Table 40]
Dimensions of Threads and Points for Type AB and Type ABR Thread-forming Screws
AB, ABR型

自攻螺纹：

2 B型 BP型自攻螺钉螺纹和末端 [Table 41] [美标]
ASME/ANSI B 18.6.3 (T41) - 2013		 B型 BP型自攻螺钉螺纹和末端 [Table 41]
Dimensions of Threads and Points for Type B and BP Thread-Forming Tapping Screws
B, BP型

自攻螺纹：

3 A型自攻螺钉螺纹和末端 [Table 42] [美标]
ASME/ANSI B 18.6.3 (T42) - 2013		 A型自攻螺钉螺纹和末端 [Table 42]
Dimensions of Threads and Points for Type A Thread-Forming Tapping Screws
A型

自攻螺纹：

4 BF型 BT型 自切自攻螺钉螺纹和末端 [Table 43] [美标]
ASME/ANSI B 18.6.3 (T43) - 2013		 BF型 BT型 自切自攻螺钉螺纹和末端 [Table 43]
Dimensions of Threads and Points for Types BF and BT Thread-Cutting Tapping Screws
BF, BT型

自攻螺纹：

5 D, F, G, T 型自攻螺钉 螺纹和末端 [Table 44] [美标]
ASME/ANSI B 18.6.3 (T44) - 2013		 D, F, G, T 型自攻螺钉 螺纹和末端 [Table 44]
Dimensions of Threads and Points for Type D, F, G, and T Thread-Cutting Tapping Screws
D, F, G, T型

自攻螺纹：

6 自挤自攻【TRS型】螺纹和末端 [Table 45] [美标]
ASME/ANSI B 18.6.3 (T45) - 2013		 自挤自攻【TRS型】螺纹和末端 [Table 45]
Dimensions of Type TRS Tapping Screws
TRS型

引用参考

GB /T 3098.5 - 2016
紧固件机械性能 - 自攻螺钉
GB /T 1172 - 1999
黑色金属硬度及强度换算值
GB /T 5267.1 - 2002
镀锌、镀镍、镀镉、复合镀等层镀层盐雾腐蚀的防护性能
GB /T 193 - 2003
普通螺纹（一般用途米制螺纹）- 直径与螺距系列 (ISO 261: 1998, MOD)
GB /T 5280 - 2002
自攻螺钉用螺纹
注：技术数据仅供参考，请以官方原件为准！
类似标准及供货信息
7 开槽半沉头自攻螺钉 [国标]
GB /T 5284 - 2017		 开槽半沉头自攻螺钉
Slotted Raised Countersunk(Oval) Head Tapping Screws
8 开槽半沉头自攻螺钉 [国标]
GB /T 5284 - 1985		 开槽半沉头自攻螺钉
Slotted Raised Countersunk Head Tapping Screws
9 米制开槽半沉头自攻钉 [美标]
IFI 502 - 1982		 米制开槽半沉头自攻钉
Metric Slotted Oval Countersunk Head Tapping Screws
10 开槽半沉头自攻螺钉 [德标]
DIN 7973 - 1990		 开槽半沉头自攻螺钉
Slotted Raised Countersunk Head Tapping Screws
供应商(3)
11 开槽半沉头自攻螺钉 [国际]
ISO 1483 - 2011		 开槽半沉头自攻螺钉
Slotted Raised Countersunk (Oval) Head Tapping Screws
12 开槽半沉头自攻螺钉 [国际]
ISO 1483 - 1983		 开槽半沉头自攻螺钉
Slotted raised countersunk head tapping screws
13 开槽半沉头自攻钉 [表JA5] [日标]
JIS B 1115 (JA5) - 2015		 开槽半沉头自攻钉 [表JA5]
Slotted Raised countersunk head tapping screws [Table JA5]
14 开槽半沉头自攻螺钉 [Table 9] [日标]
JIS B 1115 (T9) - 2015		 开槽半沉头自攻螺钉 [Table 9]
Slotted Raised Countersunk Head Tapping Screws [Table 9]
15 开槽半沉头自攻钉 [表3] [日标]
JIS B 1115 (T3) - 1996		 开槽半沉头自攻钉 [表3]
Slotted raised countersunk head tapping screws [Table 3]
16 开槽半沉头自攻钉 [附表3] [日标]
JIS B 1115 (AT3) - 1996		 开槽半沉头自攻钉 [附表3]
Slotted Raised countersunk head tapping screws [Annex Table 3]
17 80°开槽半沉头自攻钉 [美标]
ASME/ANSI B 18.6.3 - 2010		 80°开槽半沉头自攻钉
80° Machine Screw and Tapping Screw Nuts (Inch Seires)
18 开槽半沉头自攻螺钉 [法国]
NF E 25-661 - 1994		 开槽半沉头自攻螺钉
Slotted Raised Countersunk (Oval) Head Tapping Screws
19 开槽80°半沉头自攻钉 [Table 12] [英标]
BS 4174 - 1972		 开槽80°半沉头自攻钉 [Table 12]
80°Slotted Raised Countersunk Head Tapping Screws [Table 12]
20 米字槽80°半沉头自攻钉 [Table 13] [英标]
BS 4174 - 1972		 米字槽80°半沉头自攻钉 [Table 13]
Cross Recess 80° Raised Countersunk Head Tapping Screws [Table 13]
21 开槽80°半沉头清根自攻钉 [Table 14] [英标]
BS 4174 - 1972		 开槽80°半沉头清根自攻钉 [Table 14]
Slotted 80° truncated Raised Countersunk Head Screws [Table 14]
22 米制开槽半沉头自攻螺钉 [澳标]
AS /NZS 4405 - 1996		 米制开槽半沉头自攻螺钉
ISO metric slotted raised countersunk head tapping screws
23 开槽半沉头自攻螺钉 [德标]
DIN EN ISO 1483 - 2011		 开槽半沉头自攻螺钉
Slotted Raised Countersunk (Oval) Head Tapping Screws
供应商(3)
24 82°开槽半沉头 AB ABR 自攻螺钉 [美标]
ASME B 18.6.3 (H2A+T1A) - 2024		 82°开槽半沉头 AB ABR 自攻螺钉
82° Dimensions of Slotted Oval Countersunk Head Tapping Screws
25 80° 开槽半沉头清根 AB、ABR型自攻螺钉 [美标]
ASME B 18.6.3 (H3C+T1A) - 2024		 80° 开槽半沉头清根 AB、ABR型自攻螺钉
80° Slotted Undercut Oval Countersunk Head Tapping Screws - Type AB、ABR
26 82°开槽半沉头 AB ABR 自攻螺钉 [Table 7] [美标]
ASME B 18.6.3 (T7+T40) - 2013		 82°开槽半沉头 AB ABR 自攻螺钉 [Table 7]
82° Dimensions of Slotted Oval Countersunk Head Tapping Screws [Table 7]
27 米制开槽半沉头自攻钉 [Table 12] [美标]
ASME B 18.6.5M (T12) - 2000 (R2010)		 米制开槽半沉头自攻钉 [Table 12]
Metrice slotted raised countersunk head tapping screws [Table 12]
28 开槽半沉头自攻螺钉 B,BP型 [Table 20] [美标]
ASME B 18.6.4 - 1998		 开槽半沉头自攻螺钉 B,BP型 [Table 20]
slotted Oval Countersunk Head Tapping Screws - Type B and BP Thread Forming [Table 20]
29 开槽半沉头自攻螺钉 C型(统一螺纹) [Table 20] [美标]
ASME B 18.6.4 - 1998		 开槽半沉头自攻螺钉 C型(统一螺纹) [Table 20]
slotted Oval Countersunk Head Tapping Screws - Type C Thread Forming [Table 20]
30 开槽半沉头自攻螺钉 AB型 [Table 20] [美标]
ASME B 18.6.4 - 1998		 开槽半沉头自攻螺钉 AB型 [Table 20]
slotted Oval Countersunk Head Tapping Screws - Type AB Thread Forming [Table 20]
31 开槽半沉头自攻螺钉 A型 [Table 20] [美标]
ASME B 18.6.4 - 1998		 开槽半沉头自攻螺钉 A型 [Table 20]
slotted Oval Countersunk Head Tapping Screws - Type A Thread Forming [Table 20]
© 易紧通 服务热线：4006-164580（免长途费）