会员中心 | English

开槽半沉头螺钉 DIN 964 - 1990

选择规格尺寸点击↓

M1.2

M1.4

M1.6

M2.5

(M3.5)

M10

括号内尺寸为非优选

尺寸单位: mm

模型下载

模型下载替

扫一扫分享

单重计算公差公制螺纹极限尺寸米/英制螺纹对照螺纹直径与受力截面积最小破坏扭矩牌号等级毛坯直径

千件重及价格计算千件重 : kg x 元/kg = 元/千件

默认密度 g/cm³

螺纹尺寸
d

M1.2

M1.4

M1.6

M2.5

(M3.5)

M10

P	螺距
a	最大值
d_k	最大值=公称
d_k	最小值
f	≈
k	最大值
n	公称
	最大值
	最小值
r	最大值
R	≈
t	最大值
t	最小值
x	最大值

0.25	0.25	0.3	0.35	0.4	0.45	0.5	0.6	0.7	0.8	1	1.25	1.5
0.5	0.5	0.6	0.7	0.8	0.9	1	1.2	1.4	1.6	2	2.5	3
1.9	2.3	2.6	3	3.8	4.7	5.6	6.5	7.5	9.2	11	14.5	18
1.76	2.06	2.46	2.86	3.5	4.4	5.3	6.14	7.14	8.84	10.57	14.07	17.5
0.25	0.3	0.35	0.4	0.5	0.6	0.75	0.9	1	1.25	1.5	2	2.5
0.6	0.72	0.84	0.96	1.2	1.5	1.65	1.93	2.2	2.5	3	4	5
0.25	0.3	0.3	0.4	0.5	0.6	0.8	0.8	1	1.2	1.6	2	2.5
0.45	0.5	0.5	0.6	0.7	0.8	1	1	1.2	1.51	1.91	2.31	2.81
0.31	0.36	0.36	0.46	0.56	0.66	0.86	0.86	1.06	1.26	1.66	2.06	2.56
0.1	0.12	0.14	0.16	0.2	0.25	0.3	0.35	0.4	0.5	0.6	0.8	1.0
2	2.5	3	3	4	5	6	7	8	10	12	16	20
0.5	0.6	0.65	0.8	1	1.2	1.45	1.7	1.9	2.3	2.8	3.7	4.6
0.4	0.5	0.52	0.65	0.8	1	1.2	1.4	1.6	2	2.4	3.2	4
-	-	-	0.9	1	1.1	1.25	1.5	1.75	2	2.5	3.2	3.8

千件钢制重≈kg

螺纹长度b

最小值

①,材料：
a)钢，强度等级(材料)：4.8,5.8,8.8. 标准DIN ISO 898-1
b)不锈钢，强度等级(材料)：A2-70，A4-70. 标准DIN 267-11
c)有色金属，强度等级(材料)：CuZn=铜锌合金，CU2或CU3由制造商选择。标准DIN 267-18
d)其他强度等级或材料或某种材料，例如 CU3，按协议

替代列表

DIN 964 - 1990 DIN EN ISO 2010 - 1994

等效标准

国标 GB	国际 ISO	德标 DIN
GB /T 69	ISO 2010	DIN EN ISO 2010

以上有部分标准可能为近似等效，如有异议以标准原件为准

技术条件和引用标准

材料

钢

不锈钢

有色金属

通用要求
螺纹	公差
	标准
机械性能	等级
	标准
公差	产品等级
	标准
表面处理	-
	-
表面粗糙度
表面缺陷
验收及包装
备注

DIN 267 part 1
≤ M1.4：6h ＞M1.4：6g^①
DIN 13 part 13,15
4.8，5.8，8.8	A2-70，A4-70	CuZn = 铜锌合金 CU2或CU3由制造商选择
DIN ISO 898 part 1	DIN 267 part 11	DIN 267 part 18
A
DIN ISO 4759 part 1
不经处理 8.8：blackened （thermally or chemically）	blank	blank
电镀 DIN 267 part 9
DIN 267 part 2
DIN 267 part 19
DIN 267 part 5
① Only for screws without surface protection. 6 g makes it possible for normal coating thicknesses to be applied in accordance with DIN 267 part 9, the reference line not being exceeded. Depending on the coating thickness required, a larger fundamental deviation shall be selected than that for the g position. This might, however, impair the resistance to stripping of the bolt / nut assembly.

引用参考

GB /T 1172 - 1999

黑色金属硬度及强度换算值

GB /T 5267.1 - 2002

镀锌、镀镍、镀镉、复合镀等层镀层盐雾腐蚀的防护性能

GB /T 193 - 2003

普通螺纹（一般用途米制螺纹）- 直径与螺距系列 (ISO 261: 1998, MOD)

GB /T 3106 - 2016

紧固件 - 螺栓、螺钉和螺柱 - 公称长度和螺纹长度 (ISO 888:2012, MOD)

GB /T 3 - 1997

普通螺纹收尾、肩距、退刀槽和倒角 (ISO 3508:1976 / ISO 4755:1983)

GB /T 5779.1 - 2000

紧固件表面缺陷 - 螺栓、螺钉和螺柱 - 一般要求

GB /T 5779.3 - 2000

紧固件表面缺陷 - 螺栓、螺钉和螺柱 - 特殊要求

注：技术数据仅供参考，请以官方原件为准！

告诉我在“易紧通”看到，将给您优惠

惠州市昇沪汽车紧固件科技有限公司

联系人：黄俊辉

1540428407 移动电话： 13828802165 电话：0752-3951888, 3951820, 3951821, 3951825, 3951826 Email:

登陆后可见

材质：1008钢、1018#碳钢、Q235碳钢、35#合金钢、304HC不锈钢、316HC不锈钢，表面处理：环保彩锌、环保蓝白锌、环保黑锌、环保镍、热镀锌、达克罗、以及非环保电镀，规格：齐全

[询价]

东台勃林邦五金科技有限公司

联系人：徐明光

278446734@qg.com 移动电话： 13305198373（徐明光）；15358251989（柳崇兴）电话：0515-85521989 Email:

登陆后可见

材质：304，316；规格范围：M2-M8；支持非标定制

[询价]

类似标准及供货信息

1	[国标] GB /T 69 - 2016	开槽半沉头螺钉 Slotted Raised Countersunk Head Screws 供应商(1)
2	[国标] GB /T 69 - 2000	开槽半沉头螺钉 Countersunk Slotted Raised Head Screws (Common Head Style) 供应商(1)
3	[国标] GB 69 - 1985	开槽半沉头螺钉 Slotted Raised Countersunk Head Screws 供应商(1)
4	[国标] GB 949 - 1988	开槽半沉头不脱出螺钉 Slotted Raised Countersunk Head Screws with Waisted Shank
5	[美标] IFI 513 - 1982	米制开槽半沉头机械螺钉 Table 4 Metric Slotted Oval Countersunk Head Machine Screws
6	[德标] DIN 924 - 2012	开槽半沉头圆柱端螺钉 Slotted Raised Countersunk Head Screws With Dog Point
7	[德标] DIN 924 - 2006	开槽半沉头圆柱端螺钉 Slotted Raised Countersunk Head Screws With Dog Point
8	[国际] ISO 2010 - 2011	一字槽半沉头螺钉(普通头型).产品等级A Slotted Raised Countersunk Head Screws - Product Grade A 供应商(1)
9	[国际] ISO 2010 - 1994	开槽半沉头螺钉(通用头型) 产品等级A级 Countersunk slotted raised head screws (common head style); product grade A 供应商(1)
10	[日标] JIS B 1101 (T10) - 2017	开槽半沉头螺钉表10 Slotted Raised Countersunk Head Screws - Table 10
11	[日标] JIS B 1101 (JA5) - 2017	开槽半沉头螺钉附表JA.5 Slotted Raised Countersunk Head Screws - Table JA.5
12	[日标] JIS B 1116 - 2009	精密机械用开槽半沉头螺钉 Slotted Raised Countersunk Head Screws For Fine Mechanics
13	[日标] JIS B 1101 (AT4) - 1996	开槽半沉头螺钉表4 [Attached Table 4] Slotted Raised Countersunk Head Screws [Attached Table 4]
14	[日标] JIS B 1101 (AAT3) - 1996	开槽半沉头螺钉附表3 [Annex Attached Table 3] Slotted Raised Countersunk Head Screws [Annex Attached Table 3]
15	[日标] JIS B 1119 (1CFC) - 1986	眼镜框架用 - 开槽倒角半沉头螺钉 Spectacle Frames - Slotted Chamfered Flat Countersunk Machine Screws
16	[日标] JIS B 1119 (1RFC) - 1986	眼镜框架用 - 开槽弧面半沉头螺钉 Spectacle Frames - Slotted Round Flat Countersunk Machine Screws
17	[美标] ASME/ANSI B 18.6.3 - 2010	开槽半沉头螺钉Table7 Slottted Oval Countersunk Head Machine Screws
18	[美标] ASME/ANSI B 18.6.3 (T11) - 2010	80°开槽半沉头清根螺钉Table11 80° Slotted undercut oval countersunk head machine screws
19	[美标] ASME/ANSI B 18.6.7M - 1998	米制开槽半沉头螺钉Table6 Metric slotted raised countersunk head screws
20	[法国] NF E 25-124 - 1994	开槽半沉头螺钉 Slotted Raised Countersunk Head Screws - Product Grade A
21	[法国] NF F 03-004 (FB) - 1983	铁路车辆半沉头侧切口机械螺钉 Railway rolling stock Grade A raised countersunk notched head machine
22	[法国] NF F 03-006 (slot) - 1983	铁路车辆 A级开槽半沉头螺钉/螺母 Railway rolling stock Grade A Slotted raised countersunk head screws/nuts
23	[法国] NF F 03-006 (notch) - 1983	铁路车辆 A级沉头侧切口螺钉/螺母 Railway rolling stock Grade A notched raised countersunk head screws/nuts
24	[英标] BS 1981 - 1991	开槽半沉头螺钉(短的)Table10 Slottted Oval Countersunk Head Screws： Short Length
25	[英标] BS 1981 - 1991	开槽半沉头螺钉Table8 Slotted Raised Countersunk Head Machine Screws
26	[英标] BS 4183 (T3) - 1967	开槽半沉头机械螺钉 Slotted raised countersunk head machine screws. Metric series
27	[英标] BS 450 - 1958	英制开槽半沉头螺钉 - B.S.W. & B.S.F. 螺纹 [Table 3] Slotted 90° Raised-Countersunk Head Screws with B.S.W. & B.S.F. Threads [Table 3]
28	[澳标] AS /NZS 1427 - 1996	米制开槽半沉头螺钉 [Table 2] ISO metric slotted raised countersunk head screws [Table 2]
29	[台湾] CNS 9679 - 1982	精密机械用开槽半沉头螺钉 Slotted Raised Countersunk Head Screws For Fine Mechanics
30	[台湾] CNS 4414 - 1981	开槽半沉头螺钉 Slotted Raised Countersunk Head Screws - Product Grade A
31	[俄标] GOST 17474 - 1980	开槽半沉头螺钉 A级和B级 Raised countersunk head screws （Slotted）, product grades A and B
32	[韩标] KS B 1021 (T6) - 2012 (R2022)	开槽半沉头螺钉【Table 6】 Slotted Raised Countersunk Head Screws【Table 6】
33	[德标] DIN EN ISO 2010 - 1994	开槽半沉头螺钉(通用头型) - 产品等级A级 Slotted Raised Countersunk Head Screws (Common Head Style) - Product Grade A 供应商(2)
34	[美标] ASME B 18.6.3 (H2A) - 2024	82° 开槽半沉头机械螺钉(ASTM F837 / F468) 82° Slotted Oval Countersunk Head Machine Screws (ASTM F837 / F468)
35	[美标] ASME B 18.6.3 (H3C) - 2024	82° 开槽半沉头清根机械螺钉 (ASTM F837 / F468) 82° Slotted Undercut Oval Countersunk Head Machine Screws (ASTM F837 / F468)
36	[美标] ASME B 18.6.3 (T7) - 2013	82° 开槽半沉头机械螺钉 [Table 7] (ASTM F837 / F468) 82° Slotted Oval Countersunk Head Machine Screws [Table 7] (ASTM F837 / F468)
37	[美标] ASME B 18.6.3 (T11) - 2013	82° 开槽半沉头清根机械螺钉 [table 11] (ASTM F837 / F468) 82° Slotted Undercut Oval Countersunk Head Machine Screws [table 11] (ASTM F837 / F468)
38	[航天] QJ 2388 - 1992	开槽半沉头螺钉 Slotted countersunk raised head screws
39	[航空] HB 1- 209 - 1995	90°开槽半沉头螺钉 90° Countersunk slotted raised head screws

开槽半沉头螺钉 DIN 964 - 1990

相关材料标准或牌号

技术条件和引用标准

引用参考